Solid State Relays 1-Phase, Proportional Switching Controllers Types RGS1P..AA.., RGS1P..V.. 1-pole analog switching AC solid state relays Selectable mode of operation: - Phase Angle - Full Cycle x1, x4, x16 - Advanced Full Cycle - Soft Starting Rated operational voltage: up to 660 VAC Rated operational current: up to 90 AAC Control inputs: 4-20 mA, 0-5V, 1-5V, 0-10V, external potentiometer Integrated varistor protection on output Load ON LED indication 100kA short circuit current rating according to UL508 Product Description Ordering Key RGS 1 P 60 V 50 E D The RGS1P is a series of solid phase angle control, full cycle Solid state relay state relays that give the possi- control, advanced full cycle Number of poles bility to control output power of control specific for short wave Type of switching 1-phase loads with an analog infrared heaters and soft start- Rated operational voltage control input. The RGS1P is ing for limiting inrush current of Control input intended to be mounted on loads having a high tempera- Rated operational current chassis or an external ture coefficient. Configuration layout heatsink. External supply The output of the RGS1P is Input types cover a wide range protected against overvoltages of current and voltage ranges. by means of an integrated Local setting by an external varistor across the output. Two potentiometer is possible. front LEDs indicate the status Switching modes, selectable of the load and control. through a front knob, allow Specifications are at a surrounding temperature of 25C unless otherwise specified. Type Selection 1 2 SSR with Type of Rated voltage (Ue), Connection External supply (Us) Control input Rated current 40C, no heatsink switching Blocking voltage configuration It RGS1: P: Proportional 23: 85 - 265 VAC, AA: 50: 50 AAC, 1800 As E: Contactor D: 24 VDC/AC 1-pole 800 Vp 4-20 mADC 92: 90 AAC, 18000 As A: 90 - 250 VAC switching 48: 190 - 550 VAC, V: 1200 Vp 0-5 VDC 1- 5 VDC 60: 410 - 660 VAC, 0-10 VDC 1200 Vp External potentiometer 1: V control input versions require an external supply Us 2: Max. ratings with suitable heatsink. Refer to Heatsink Selection tables for further details. Specifications are subject to change without notice (09.04.2018) 1RGS1P..AA, RGS1P..V Selection Guide Output Control External Power connection Rated operational current (It) voltage, input supply, Product width Ue Us 50 AAC 90 AAC (1800 As) (18000 As) 35 mm 35 mm 85 - 265 VAC AA: RGS1P23AA50E - - Screw 4-20 mADC - RGS1P23AA92E Box V: 24 VDC/AC Screw RGS1P23V50ED - 0-10V, 0-5V, 1-5VDC, pot Box - RGS1P23V92ED 90-250 VAC Screw RGS1P23V50EA - Box - RGS1P23V92EA 190 - 550 VAC AA: - Screw RGS1P48AA50E - 4-20 mADC Box - RGS1P48AA92E V: RGS1P48V50ED - 24 VDC/AC Screw 0-10V, 0-5V, 1-5VDC, pot Box - RGS1P48V92ED 90-250 VAC Screw RGS1P48V50EA - Box - RGS1P48V92EA 410 - 660 VAC AA: - Screw RGS1P60AA50E - 4-20 mADC Box - RGS1P60AA92E V: 24 VDC/AC Screw RGS1P60V50ED - 0-10V, 0-5V, 1-5VDC, pot Box - RGS1P60V92ED RGS1P60V50EA - 90-250 VAC Screw Box - RGS1P60V92EA General Specifications RGS1P..AA RGS1P..V Operational frequency range 45 to 65 Hz 45 to 65 Hz Power factor > 0.7 rated voltage > 0.7 rated voltage Touch Protection IP20 IP20 3 LED status indication Green Control input Control input <4 mA, flashing 0.5s ON, 0.5s OFF <0 V, flashing 0.5s ON, 0.5s OFF >4 mA, intensity varies with input >0 V, fully ON Supply ON (Us) Supply ON (Us) n/a Flashing 0.5s ON, 0.5s OFF Yellow Load ON Load ON Pollution degree 2 (non-conductive pollution with 2 (non-conductive pollution with possibilities of condensation) possibilities of condensation) Rated impulse withstand voltage, Uimp 6 kV (1.2/50s) 6 kV (1.2/50s) Over-voltage category III (fixed installations) III (fixed installations) Isolation L1, T1, A1, A2, A3, POT, GND, Us to case 4000 Vrms 4000 Vrms L1, T1 to A1, A2, A3, Pot, GND, Us 2500 Vrms 2500 Vrms Us to A1, A2, A3, POT, GND n/a n/a (..V..ED) 1500 Vrms (..V..EA) 3: Refer to LED Indications section 2 Specifications are subject to change without notice (09.04.2018)