Solid State Relays 1-Phase, Soft Start Switching Types RGS1P..K.. 1-pole AC solid state relays Soft start switching for short wave infrared heaters Rated operational voltage: up to 660 VAC Rated operational current: up to 90 AAC Control input: 24 VDC Integrated varistor protection on output Load ON LED indication 100kA short circuit current rating according to UL508 Product Description Ordering Key RGS 1 P 48 K 50 E D The RGS1P..K provides a an accessible potentiometer. Solid state relay solution for starting of loads Once the soft start is complete, Number of poles having a high cold to hot resis- the RGS1P..K output switches Type of switching tance ratio and hence it is very ON and OFF according to the Rated operational voltage common for such loads to control signal. Soft starting is Control input exhibit a high inrush current perfomed again if the control Rated operational current when switched on from a cold signal has been missing for Configuration state. Such behaviour is very more than 5 seconds. External supply common for short wave infrared heaters. The output of the RGS1P is protected against overvoltages When a control signal is by means of an integrated applied to the RGS1P..K, a varistor across the output. Two soft start is performed. The soft front LEDs indicate the status start time is settable through of the load and control Specifications are at a surrounding temperature of 25C unless otherwise specified. Type Selection 1 SSR with Type of Rated voltage (Ue), Control input Connection External supply (Us) Rated current , no heatsink switching Blocking voltage configuration It RGS1: P: Proportional 23: 85 - 265 VAC, K: 24 VDC 50: 50 AAC, 1800 As E: Contactor D: 24 VDC/ AC 1-pole (Soft starting) 800 Vp +/-20% 92: 90 AAC, 180 00 As switching 48: 190 - 550 VAC, 1200 Vp 60: 410 - 660 VAC, 1200 Vp 1: Max. ratings with suitable heatsink. Refer to Heatsink Selection tables for further details. Specifications are subject to change without notice (17.04.2018) 1RGS1P..K Selection Guide Output Control External Power connection Rated operational current (It) voltage, input supply, Product width Ue Us 50 AAC 90 AAC (1800 As) (18000 As) 35 mm 35 mm 85 - 265 VAC 19.2 - 28.8 VDC RGS1P23K50ED - 24 VDC/AC Screw - RGS1P23K92ED Box 190 - 550 VAC 19.2 - 28.8 VDC RGS1P48K50ED - 24 VDC/AC Screw - RGS1P48K92ED Box 410 - 660 VAC 19.2 - 28.8 VDC RGS1P60K50ED - 24 VDC/AC Screw - RGS1P60K92ED Box General Specifications Operational frequency range 45 to 65 Hz Pollution degree 2 (non-conductive pollution with possibilities of Power factor > 0.7 rated voltage condensation) Touch Protection IP20 Rated impulse withstand voltage, Uimp 6 kV (1.2/50s) 2 LED status indication Over-voltage category III (fixed installations) Green Control ON, fully ON Isolation Supply ON, flashing 0.5s ON, 0.5s OFF L1, T1, A1, GND, Us to case 4000 Vrms Yellow Load ON L1, T1 to A1, GND, Us 2500 Vrms 2: Refer to LED Indications section Output Voltage Specifications RGS1P23.. RGS1P48.. RGS1P60.. Operational voltage range (Ue) 85-265 VAC 190-550 VAC 410-660 VAC Blocking voltage 800 Vp 1200 Vp 1200 Vp Leakage current rated voltage 5 mAAC 5 mAAC 5 mAAC Internal varistor across output Yes Yes Yes 2 Specifications are subject to change without notice (17.04.2018)