SHPINV2T1P124 Carlo Gavazzi

Smart Dupline Analog Input Module Type SHPINNI2 2 x Ni1000 (TK5000)/Pt1000 Bus-powered Input type selectable from SBWEB/SHWEB configuration tools Small dimension housing for decentralized installation inside wall-box Product Description Ordering Key SH P IN NI 2 SHPINNI2 is an input mod- wiring connections, reduces Smart Dupline ule with 2 x Ni1000/Pt1000 the number of DDCs and Decentralized inputs. The compact size of sub-panels required and Input module the module makes it pos- provides a higher flexibility Ni1000/Pt1000 Input sible to fit it into a wall- for last minute changes and Number of inputs box or small junction box, enhancements. The selec- thereby enabling a decen- tion of input type (Ni1000 tralized installation concept or Pt1000) and input range where the Dupline bus is to be used is done with the multidropped from sensor SBWEB/SHWEB configura- to sensor. This simplifies tion tools. Note: The accu- the wiring to the controller racy depends on the input compared to traditional star range selected. Type Selection Input number Type Supplied by Dupline 2 Ni1000 (TK5000)/Pt1000 SHPINNI2 Dupline Specifications Supply Specifications Voltage 8.2 V Power Supply Supplied by Dupline Maximum Dupline voltage 10 V Power on delay 2 s Activated (all inputs) 1 s Minimum Dupline voltage 5.5 V Maximum Dupline current 3.5 mA Specifications for Analog inputs Ni1000 Pt1000 Selected signal range -30 to 130C Selected Signal range -30 to 130C Inaccuracy (-30 to -21C) < 1.0C Inaccuracy (-30 to -21C) < 1.0C Inaccuracy (-20 to 50C) < 0.5C Inaccuracy (-20 to 50C) < 0.5C Inaccuracy (51 to 130C) < 1.0C Inaccuracy (51 to 130C) < 1.0C Cable length < 5 m Cable length < 5 m Ni1000 Pt1000 Selected signal range -30 to 250C Selected signal range -30 to 250C Inaccuracy (-30 to -21C) < 2.0C Inaccuracy (-30 to -21C) < 2.0C Inaccuracy (-20 to 50C) < 0.9C Inaccuracy (-20 to 50C) < 0.9C Inaccuracy (51 to 130C) < 2.0C Inaccuracy (51 to 130C) < 2.0C Inaccuracy (131 to 250C) < 5.0C Inaccuracy (131 to 250C) < 5.0C Cable length < 5 m Cable length < 5 m Specifications are subject to change without notice (14.09.2017) 1 SHPINNI2 General Specifications Wiring Diagram Environment D+ Pollution degree 2 (IEC 60664-1, par. 4.6.2) D- Operating temperature 0 to +50C (-4 to +122F) Storage temperature -50 to +85C (-58 to + 185F) Humidity (non-condensing) 20 - 90% Housing Material Macromel 6: Colour Ambra Ni1000 / Pt1000 input 1 Dimensions (h x w x d) 50 x 30 x 18 mm 7: GND Weight 50 g 9: Protection degree IP20 Ni1000 / Pt1000 input 2 Terminal block 10: Yellow LED Dupline bus 2 x spring terminal (double) GND 2 Cross-section area Terminal: 1.5 mm Cable x 4 6 + 9 Ni1000 (TK5000) input 7 + 10 GND 2 Cross-sectional area 0.14 mm Wire length 0.25 m Address assignment/ Channel programming The address assignment is automatic: the controller recognises the module through the SIN (Specific Dimensions Identification Number) that has to be filled in the SH tool. Dielectric strength Dupline to signal input None EMC 30 21 Immunity EN61000-6-2 - Electrostatic disharge EN61000-4-2 5 2 8.5 - Radiated radiofrequency EN61000-4-3 - Burst immunity EN61000-4-4 - Surge EN61000-4-5 - Conducted radiofrequency EN61000-4-6 - Power frequency magnetic fields EN61000-4-8 - Voltage dips, variations, interruptions EN61000-4-11 Emission - Conducted and radiated emissions CISPR 22 (EN55022), cl.B - Conducted emissions CISPR 16-2-1 (EN55016-2-1) - Radiated emissions CISPR 16-2-3 (EN55016-2-3) Approvals CE cULus according to UL60950 12 2 Specifications are subject to change without notice (14.09.2017) 53 32 18 10 GND D+ D- 9 Input 2 7 GND 6 Input 1 20