SPUC24720 Carlo Gavazzi

UPS Controller Type SPUC 30A 12 / 24V DIN Rail Mounting DIN Rail mounting UPS controller To be used in combination up to 30A power Supply Built-in battery test function Battery polarity protection Relay contact signal output LED indicator for DC Bus ok, battery fail and battery discharge Suggested batteries from 4 to 12Ah 3 years warranty Ordering Key SPUC 24 720 Model Output voltage Output power Approvals Product Description The SPUC, being a UPS The input of the SPUC has to nominal charging voltage is or blackout the SPUC will controller, it can be used to be connected to a a 12Vdc 13.6V (or 27.2V). immediately switch the either convert and existing or 24Vdc source, depending The charge is carried out in supply to the load by using conventional supply system upon the model. the first stage by constant the battery stored energy. into an uninterruptible power The output is connected to current until the nominal There are three relays for supply system or else to the load which needs to be voltage is reached then by remote operation monitoring: realize a UPS system by supplied uninterruptedly. constant voltage. DC OK provides indication using a separate power The battery, suggested type When the battery is fully of correct DC output, supply. is lead acid, is connected to charged it stays into float Battery fail indicates It is suitable for both 12V the battery terminals. cycle. Sulphatation process a possible failure of the and 24V systems and it DIN rail mounting racks is prevented by charging battery and Backup Mode can handle up to 30A load are also available, with or with positive/negative pulse provides remore indication current whilst the suggested without batteries, for easy current. that the device is providing battery sizes are from 4 to installation of the battery If the 24Vdc input is cut off power to the load from the 12Ah. aside the SPUC. The because of mains failure battery not from input. Output Performance AVAILABLE INPUT MAX. OUTPUT OUTPUT MAX. OUTPUT MODELS VOLTAGE POWER VOLTAGE CURRENT Single Output Models SPUC12360 11 ~ 14VDC 360 WATTS 10.5 ~ 13.5VDC 30A SPUC24720 22.5 ~ 28VDC 720 WATTS 22 ~ 27.5VDC 30A Input Data DC input Battery Nominal input voltage Voltage range 12V Model 12V 12V Model Min. 9.6V ~ 14.25V Max. 24V Model 24V 24V Model Min. 19.2V ~ 28.5V Max. Input voltage range Switching threshold 12V Model Min. 11 ~ 14V Max. 12V Model Vin < 11V Dynamic Vout - 1V / 100ms 24V Model Min. 22.5 ~ 28V Max. 24V Model Vin < 22.5V Dynamic Vout - 1V / 100ms Current consumption No load 0.2A Charging 3.5A Maximum 35A 1 Specifications are subject to change without notice. Pictures are just an example. For special features and/or customization, please ask to our sales network. 16/05/2016UPS Controller Type SPUC 30A 12 / 24V DIN Rail Mounting Output Data All specifications are at nominal values, full load, 25C unless otherwise noted DC output Battery output fuse 40A 32V Automotive fuse Nominal Output voltage on the front side. Replaceable. 12V Model 12V Suggested external battery 3.2Ah, 7.2Ah or 12Ah Lead 24V Model 24V Acid batteries. (SPUBAT Output voltage range series, see related Data Sheet) 12V Model Min. 10.5V ~ 13.5V Max. Charge Voltage selection 24V Model Min. 22V ~ 27.5V Max. 12V Model Current range 30A Max. Float charge voltage 13.6V Battery output Fast/bulk charge Voltage 14.25V 12V Model Min. 9.1V ~ 13.75V Max. 24V Model 24V Model Min. 18.7V ~ 28.0V Max. Float charge voltage 27.2V Current range 2.5A Fast/Bulk charge voltage 28.5V Output voltage drop Charge Current selection Vi out 0.55V 12V/24V Models Battery - Vout 0.45V 2AH ~ 5AH 0.5A Ripple and noise (Vi nom, Io nom) 100mV 5AH ~ 10AH 1A Battery max withstand >10AH 2.5A reverse voltage Suggested Discharge current 12V Model 14.25V From 0.1 to 3 times battery 24V Model 28.5V capacity 30A Max Control and Protections Battery discharge low voltage Battery Fail Output protection Relay status Output relay switches 12V Model 9.6V when battery test is 24V Model 19.2V negative Battery charging low voltage Backup Mode output is active when protection the SPUC operates as UPS 12V Model 8V as there is no input. Power 24V Model 16V i provided from battery DC OK relay output Note Carlo Gavazzi provides a (active when) set of batteries, SPUBAT 12V Version 11 to 14Vdc series. 24V Version 22.5 to 28Vdc See related Data Sheet. General Data Dimensions Packing Cartons of 32 x 0.45kg LxWxD mm (inch) 90x54x114 mm each pieces. (3.60x2.13x4.49) inches Total weight 15.5kg Case material Plastic (34.17lbs 1.85cuft) Weight 370g Signal Outputs Batt fail Yes Relay outputs Back up mode Yes Type 3 x SPDT DC OK Yes Max. AC Load 2A 115Vac / 1A 240Vac Max. DC Load 2A 30Vdc 2 Specifications are subject to change without notice. Pictures are just an example. For special features and/or customization, please ask to our sales network. 16/05/2016