Conductive Polymer Engineering Bulletin No.795 / Apr.2008 Aluminum Solid Capacitors Super low ESR, high ripple current capability Downsized from PSC series (F8B8L to F6.3B8L) Endurance is longer life than PSC series (5,000 hours at 105C) ESR after endurance is specied within the initial spec Rated voltage range : 2.5 to 6.3Vdc RoHS Compliant Halogen Free SPECIFICATIONS Items Characteristics Category -55 to +105C Temperature Range Rated Voltage Range 2.5 to 6.3Vdc Capacitance Tolerance P20% (M) (at 20C, 120Hz) Surge Voltage Rated voltage(V)B1.15 (at 105C) Leakage Current I=0.2CV or 500MA, whichever is greater *Note Where, I : Leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V) (at 20C after 2 minutes) Dissipation Factor 0.10 max. (tane) (at 20C, 120Hz) Low Temperature Z(-25C)/Z(+20C) 1.15 Characteristics Z(-55C)/Z(+20C) 1.25 (Max.Impedance Ratio) (at 100kHz) Endurance The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 5,000 hours at 105C. Appearance No significant damage Capacitance change P20% of the initial value D.F. (tanE) The initial specified value ESR The initial specified value Leakage current The initial specified value Bias Humidity Test The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to DC voltage at 60C, 90 to 95% RH for 1,000 hours. Appearance No significant damage Capacitance change P20% of the initial value D.F. (tanE) The initial specified value ESR The initial specified value Leakage current The initial specified value Surge Voltage Test The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds. Appearance No significant damage Capacitance change P20% of the initial value D.F. (tanE) The initial specified value ESR The initial specified value Leakage current The initial specified value Halogen Free All homogeneous materials within a capacitor meet the criteria in Table-1 and Tabel-2. (Definition) Homogeneous material has uniform composition throughout and cannot be mechanically disjointed into different materials. Table-1 Table-2 Substance Permissible limit (by weight) Substance Permissible limit (by weight) Bromine (Br) 900ppm (0.09%) Antimony Trioxide (Sb O ) 1,000ppm (0.10%) 2 3 Chlorine (Cl) 900ppm (0.09%) Red Phosphorus 1,000ppm (0.10%) Total concentration of 1,500ppm (0.15%) Chlorine (Cl) + Bromine (Br) Failure Rate 0.5% per 1,000 hours maximum (Confidence level 60% at 105C) *Note : If any doubt arises, measure the leakage current after the following voltage treatment. Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105C. DIMENSIONS mm Terminal Code : E MARKING Coated Case Size code F08 EX) 2.5V820MF fD 6.3 fd 0.6 6D6 E F 2.5 820 fD FD+0.5max. V 2.5 L L+1.5max. L 15min. 4min. Speci cations in this bulletin are subject to change without notice. 1 NIPPON CHEMI-CON CORPORATION 1435 Halogen Free Downsized Long Life FD Fd FP0.5Conductive Polymer Engineering Bulletin No.795 / Apr.2008 Aluminum Solid Capacitors PART NUMBERING SYSTEM 132645178910 11213 14 15 16 17 18 A P S E 2 R 5 E A A 5 6 1 M F 0 8 S Supplement code Size code Capacitance tolerance code Capacitance code (ex. 820MF:821) Lead formingTaping code Terminal code Voltage code (ex. 2.5V:2R5, 4V:4R0, 6.3V:6R3) Series code Category STANDARD RATINGS Case size ESR Rated ripple current WV(Vdc) Cap(mF) Part No. fDbL(mm) (mo max./20c, 100k to 300kHz) (mArms/105c, 100kHz) 2.5 820 6.3B8 7 5,000 APSE2R5ESS821MF08S 4 560 6.3B8 7 5,000 APSE4R0ESS561MF08S 470 6.3B8 8 4,700 APSE6R3ESS471MF08S 6.3 560 6.3B8 8 4,700 APSE6R3ESS561MF08S SS : Enter the appropriate lead forming or taping code. Speci cations in this bulletin are subject to change without notice. 2 NIPPON CHEMI-CON CORPORATION 1435