SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS Low ESR, 105 New TM AIchip -MZRSeries MZR Downsizing and Lower ESR, 2,000hours at 105 Rated voltage range : 6.3 to 50V, Nominal capacitance range : 100 to 2,200F Downsized Solvent resistant type MZJ P86 Vibration resistance structure RoHS Compliant SPECIFICATIONS Items Characteristics Category -55 to +105 Temperature Range Rated Voltage Range 6.3 to 35Vdc Capacitance Tolerance 20% (M) (at 20, 120Hz) Leakage Current I=0.01CV or 3A, whichever is greater. Where, I : Max. leakage current (A), C : Nominal capacitance (F), V : Rated voltage (V) (at 20 after 2 minutes) Dissipation Factor Rated voltage (Vdc) 6.3V 10V 16V 25V 35V 50V (at 20 , 120Hz) (tan) tan(Max.) 0.26 0.19 0.16 0.14 0.12 0.10 Low Temperature Rated voltage (Vdc) 6.3V 10V 16V 25V 35V 50V (at 120Hz) Characteristics Z(-25)/Z(+20) 2 2 2 2 2 2 (Max. Impedance Ratio) Z(-40)/Z(+20) 3 3 3 3 3 3 Z(-55)/Z(+20) 4 4 4 3 3 3 Endurance The following specifications shall be satisfied when the capacitors are restored to 20 after the rated voltage is applied for 2,000 hours at 105. Capacitance change 30% of the initial value D.F. (tan) 200% of the initial specified value Leakage current The initial specified value Shelf Life The following specifications shall be satisfied when the capacitors are restored to 20 after exposing them for 1,000 hours at 105 without voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4. Capacitance change 30% of the initial value D.F. (tan) 200% of the initial specified value Leakage current The initial specified value Surge Voltage Test The capacitors shall be subjected to 1,000 cycles each consisting of charging with the specified surge voltage for 305 seconds through a protective resistor (as required for RC=0.10.05sec) and open-circuiting for 5.5 minutes at a room temperature of 15 to 35. Rated voltage (V ) 6.3V 10V 16V 25V 35V 50V dc Surge voltage (Vdc) 7.2V 12V 18V 29V 40V 57V Appearance No significant damage Capacitance change 20% of the initial value D.F. (tan) 200% of the initial specified value Leakage current The initial specified value (Caution) Surge Voltage Test intends to evaluate capacitors in durability of an exceptional excessive voltage under specific conditions.It does not imply long-term use at all. DIMENSIONS mm Terminal Code : A Terminal Code : G(Vibration resistant structure) Size code : F80 to JA0 Size code : HA0 and JA0 Size code D L A B C W P F80 6.3 7.7 6.6 6.6 7.2 0.5 to 0.8 1.9 W 0.3max. Vent for JA0 Vent for JA0 HA0 8 10.0 8.3 8.3 9.0 0.7 to 1.1 3.1 W JA0 10 10.0 10.3 10.3 11.0 0.7 to 1.1 4.5 A0.2 L0.5 0.3max. A0.2 L0.3 (Note) Note : L0.5 for HA0 and JA0 : Dummy terminals MARKING EX) 35V330F Rated voltage symbol Rated voltage (Vdc) 6.3 10 16 25 35 50 3Q Symbol j A C E V H 330 ZR V Applying voltage over the rated voltages causes the capacitors to have short lifetime. Besides, applying voltage over the specied surge voltages may cause to have short circuit failure. A protection circuit should be used if applied voltage will exceed the rated voltages. Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. 84 CAT. No. E1001O D0.5 B0.2 P C0.2 D0.5 B0.2 P C0.2SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS Low ESR, 105 New TM AIchip -MZRSeries PART NUMBERING SYSTEM 1 2 3 4 5 6 78 9 10 11 12 13 14 15 16 17 18 E MZR AAA A DA AAA M AAA G Supplement code Size code Capacitance tolerance code Capacitance code (ex. 220F:221, 470F:471) Taping code Terminal code (A, G) Voltage code (ex. 6.3V:6R3, 10V:100, 35V:350) Series code Category Please refer toProduct code guide (surface mount type STANDARD RATINGS WV Cap ESR Rated ripple current Size code tan Part No. (Vdc) (F) ( max./20 , 100kHz) (mArms/105 , 100kHz) 680 F80 0.26 0.16 600 EMZR6R3ADA681MF80G 6.3 1,500 HA0 0.26 0.08 850 EMZR6R3DA152MHA0G 2,200 JA0 0.26 0.06 1,190 EMZR6R3DA222MJA0G 470 F80 0.19 0.16 600 EMZR100ADA471MF80G 10 1,000 HA0 0.19 0.08 850 EMZR100DA102MHA0G 1,500 JA0 0.19 0.06 1,190 EMZR100DA152MJA0G 330 F80 0.16 0.16 600 EMZR160ADA331MF80G 16 680 HA0 0.16 0.08 850 EMZR160DA681MHA0G 1,000 JA0 0.16 0.06 1,190 EMZR160DA102MJA0G 220 F80 0.14 0.16 600 EMZR250ADA221MF80G 25 470 HA0 0.14 0.08 850 EMZR250 DA471MHA0G 820 JA0 0.14 0.06 1,190 EMZR250 DA821MJA0G 150 F80 0.12 0.16 600 EMZR350ADA151MF80G 35 330 HA0 0.12 0.08 850 EMZR350DA331MHA0G 560 JA0 0.12 0.06 1,190 EMZR350DA561MJA0G 100 F80 0.10 0.34 350 EMZR500ADA101MF80G 50 220 HA0 0.10 0.18 670 EMZR500DA221MHA0G 330 JA0 0.10 0.12 900 EMZR500DA331MJA0G : Enter the appropriate terminal code. RATED RIPPLE CURRENT MULTIPLIERS Frequency Multipliers Frequency(Hz) 120 1k 10k 100k Capacitance(F) 100 to 150 0.40 0.75 0.90 1.00 220 to 560 0.50 0.85 0.94 1.00 680 to 2,200 0.60 0.87 0.95 1.00 The endurance of capacitors is reduced with internal heating produced by ripple current at the rate of halving the lifetime with every 5 rise. When long life performance is required in actual use, the rms ripple current has to be reduced. Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. 85 CAT. No. E1001O