KTS101B224M31N0T00 Chemi-Con

MULTILAYER CERAMIC CHIP CAPACITORS RoHS Compliant / Temperature cycle : 1000 cycles FEATURES 1. Large capacitance by small size. 2. Excellent noise absorption. 3. High permissible ripple current capability. 4. NTF: Temperature cycle : 1000 cycles. APPLICATIONS 1. Smoothing circuit of DC-DC converters. 2. On-board power supplies. 3. Voltage regulators for computers. 3. Noise suppressor for various kinds of equipments. 4. High reliability equipments. CONSTRUCTION Ceramic Dielectric Termination (Tin Plating) Internal Electrode RATINGS 1. Category Temperature Range -55 to +125 2. Rated Voltage Range 25, 50, 100, 250Vdc 3. Rated Capacitance Range 0.033 to 33 F 4. Rated Capacitance Tolerance M ( 20%) : Standard, K ( 10%) 5. Temperature Characteristics X7R 6. Rated Ripple Current See No.5 on the following table SPECIFICATIONS No. Items Specification Test Condition 1 Withstand Voltage No abnormality. 250% of rated voltage shall be applied for 5 seconds. (Only 250Vdc product : 475V) 2 Insulation Resistance 100/CR(M ) or 4000(M ) Rated voltage shall be applied for 60 5 seconds at temperature 25 2 . whichever is less. 3 Rated Capacitance Within specified tolerance. CR 10FCR>10 F Temperature 25 2 4 Dissipation Factor 5.0% maximum. Frequency 1 0.1kHz 120 12Hz Voltage 1 0.2Vrms 0.5 0.2Vrms 10kHz 1MHz (sine curve) 5 Rated Ripple Current Size code 31 32 43 55 Ripple voltage Vp shall be less than Arms 0.3 0.5 1.0 2.0 the rated voltage. Product speci cations in this catalog are subject to change without notice.Request our product speci cations before purchase and/or use. Please use our products based on the information contained in this catalog and product speci cations. (1/4) CAT. No. E1002R MULTILAYER CERAMIC CHIP CAPACITORS / SPECIFICATIONS No. Items Specification Test Condition 6 Adhesion No visible damage. Substrate 5N (0.51kgf) for 10 1 seconds Capacitor 7 Bend strength of the face plating Appearance : No visible damage. The substrate shall be bend at a rate of 1mm/s C/C : 15% for 5 seconds. Press bar Press Capacitor Substrate Bending capability* 45 2mm 45 2mm Support *Bending capability NTS : 1mm NTF : 1mm or 2mm 8 Solderability Min. 75% of surface of the termination Solder Pb Free Eutectic shall be covered with new solder Solder Temperature 245 5 235 5 Dipping Time 2 0.5sec. 9 Resistance to Soldering Heat Appearance : No visible damage. Solder Temperature : 260 5 C/C : 15% Dipping Time : 2 0.5 seconds D.F. : To meet the initial specification. I.R. : To meet the initial specification. 10 Temperature Cycle Appearance : No visible damage. Step Temperature ( ) (min.) C/C : 15% 1 Min. Category temperature 3 30 3 D.F. : To meet the initial specification. 2 Room temperature 3 max. I.R. : To meet the initial specification. 3 Max. Category temperature 3 30 3 4 Room temperature 3 max. For above temperature cycle. NTS : For 5 cycles NTF : For 1000 cycles 11 Humidity Load Life Appearance : No abnormality. Temperature : 40 2 Humidity : 90 to 95%RH C/C : 15% D.F. : 10% maximum Voltage : Rated voltage 24 I.R. : 25/CR(M ) or 1000(M ) Time : 500 hours 0 whichever is less. 12 Endurance Appearance : No abnormality. Temperature : 125 3 Voltage : Rated voltage C/C : 15% 48 D.F. : 10% maximum Time : 1000 hours 0 I.R. : 50/CR(M ) or 1000(M ) whichever is less. *CR : Rated Capacitance( F) Product speci cations in this catalog are subject to change without notice.Request our product speci cations before purchase and/or use. Please use our products based on the information contained in this catalog and product speci cations. (2/4) CAT. No. E1002R