Isopropanol 100% Pure 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION Product Name: ChemTools isopropanol alcohol (IPA) Part Number: CT-ISO Available Sizes: isopropanol - IPA 100% Pure Pen CT-ISO-DP isopropanol - IPA 100% Pure 1L CT-ISO1L isopropanol - IPA 100% Pure 5L CT-ISO5L isopropanol - IPA 100% Pure 20L CT-ISO20L isopropanol - IPA 100% Pure 200L CT-ISO200L Product Type: Solvent for industrial use. Company Address: ChemTools Pty. Ltd., PO Box 463, Emu Plains, NSW 2750 Ph: 02 4735 3126 EMERGENCY PHONE: Australia: Poisons Information Centre 13 11 26 International: Infotrac (708) 918 1900 2. COMPOSITION/INFORMATION ON INGREDIENTS Hazardous components CAS % HSIS TWA HSIS STEL 3 3 Propan-2-ol 67-63-0 100 400ppm (983mg/m ) 500ppm (1,230mg/m ) 3. HAZARDS IDENTIFICATION Hazard Classification: Hazardous Substance, Dangerous Goods by the criteria of SafeWork Australia. Risk Phrases: R11 Highly flammable R36/38 Irritating to eyes and skin. R67 Vapours may cause drowsiness and dizziness. Safety Phrases: S2 Keep out of reach of children S7 Keep container tightly closed S21 When using do not smoke S51 Use only in well ventilated areas. S24/25 Avoid contact with skin and eyes. Relevant routes of exposure: Skin, Inhalation, Eyes Potential Health Effects Inhalation: May cause respiratory tract irritation. High concentrations of vapours may cause headache, fatigue, drowsiness and dizziness. Skin contact: May cause allergic skin reaction. May cause skin irritation. Product has a defatting effect on skin. Prolonged contact may cause dryness of skin. Eye contact: Contact with eyes will cause irritation. 4. FIRST AID MEASURES Inhalation: Remove to fresh air. If symptoms develop and persist, get medical attention. Skin contact: Wash with soap and water. Remove contaminated clothing and shoes. Wash clothing before reuse. Get medical attention if symptoms occur. Eye contact: Check for and remove any contact lenses. Immediately flush with copious amounts of water, preferably, Lukewarm water for at least 15 minutes, holding eyelids open all the time. Get medical attention. Ingestion: Do not induce vomiting. Rinse mouth thoroughly. Loosen any tight clothing. Keep individual calm. Obtain medical attention. 5. FIRE-FIGHTING MEASURES Flash point: 12C (Abel) Autoignition temperature: 425C (ASTM D-2155) Flammable/Explosive limits-lower %: 2% Flammable/Explosive limits-upper %: 12% Extinguishing media: Alcohol resistant foam, dry chemical or carbon dioxide. Special fire fighting procedures: None Unusual fire or explosion hazards: None Hazardous combustion products: Oxides of carbon. Keep run-off water out of sewers and water sources. Hazchem Code: 2 Y E 6. ACCIDENTAL RELEASE MEASURES Environmental precautions: Extinguish all ignition sources. Ventilate well. Use approved respirator if air contamination is above accepted level. Prevent product from entering drains or open waters. info chemtools.com.au www.chemtools.com.au Isopropanol 100% Pure Clean-up methods: Soak up with inert absorbent. Store in a partly filled, closed container until disposal. 7. HANDLING AND STORAGE Handling: Avoid contact with eyes, skin and clothing. Avoid breathing vapour and mist. Wash thoroughly after handling. Storage: For safe storage, store at or below 38C (100F). Keep in a cool, well ventilated area away from heat, sparks and Open flame. Keep container tightly closed until ready for use. Incompatible products: Refer to Section 10. 8. EXPOSURE CONTROLS / PERSONAL PROTECTION Engineering controls: No specific ventilation requirements noted, but forced ventilation may still be required if concentrations exceed occupational exposure limits. Respiratory protection: Use NIOSH approved respirator if there is potential to exceed exposure limit(s). Skin protection: Use impermeable gloves and protective clothing as necessary to prevent skin contact. Neoprene gloves. Butyl rubber gloves. Natural rubber gloves. Eye/face protection: Safety goggles or safety glasses with side shields. See Section 2 for exposure limits. 9. PHYSICAL AND CHEMICAL PROPERTIES Physical state: Liquid. Colour: Clear, colourless. Odour: Organic solvents. pH: Not available Boiling point/range: 82-83C. Melting point/range: -88C Specific gravity: 0.785 at 20C. Vapour density: 2 at 20C (air=1) Evaporation rate: 1.5 (ASTM D-3539, nBuAc=1) Solubility in water: Completely miscible. 10. STABILITY AND REACTIVITY Stability: Stable under normal conditions of use. Hazardous polymerization: Will not occur. Hazardous decomposition products: Oxides of carbon. Incompatibility: Strong oxidizers. Strong acids. Conditions to avoid: SeeHandling and Storag (Section 7) andIncompatibilit (Section 10). 11. TOXICOLOGICAL INFORMATION Product toxicity data: Propan-2-ol Oral: LD >2,000 mg/Kg (rat). Skin: LD >2,000mg/Kg (rabbit) Inhalation 50 50 LC :20mg/L/8hr (rat) 50 12. ECOLOGICAL INFORMATION Acute Toxicity Fish: Low Toxicity: LC/EC/IC50 >100mg/L Aquatic Invertebrates: Low Toxicity: LC/EC/IC50 >1000mg/L Algae: expected to have Low Toxicity: LC/EC/IC50 >1000mg/L Microorganisms: Low Toxicity: LC/EC/IC50 >1000mg/L Mobility: Dissolves in water If product enters soil, it will be highly mobile and may contaminate groundwater Persistence/degradability: Readily biodegradable meeting the 10 day window criterion. Oxidises rapidly by photo-chemical reactions in air. Bioaccumulation : Not expected to bioaccumulate significantly. 13. DISPOSAL CONSIDERATIONS Recommended method of disposal: Recover or recycle if possible. Dispose of according to Federal, State and local governmental regulations. Container disposal: Drain container thoroughly. After draining, vent in a safe place away from sparks and fire. Recycle if possible. info chemtools.com.au www.chemtools.com.au