CHB200W12 SERIES 200 WATT 12:1 INPUT ISOLATED DC-DC CONVERTER Features Efficiency Up to 90% Fixed Switching Frequency Regulated Outputs Remote On/Off Fully protected (OTP/OCP/OVP/UVLO) 3000Vac I/O Isolation Operating Case Temperature -40 to +100 Half Brick Size Meet Industrial Standard 2.282.40x0.50 CB Test Certificate IEC62368-1 EN50155 Compliant with External Circuits UL62368-1 2nd (Reinforce Insulation) Approval Shock & Vibration EN50155 (EN61373) Compliant Fire & Smoke EN45545-2 Compliant 5000m Operating Altitude OUTPUT CURRENT INPUT CURRENT % EFF. MODEL INPUT OUTPUT CAPACITOR NUMBER VOLTAGE VOLTAGE LOAD MAX. MIN. MAX. NO LOAD FULL LOAD (1) (2) CHB200W12-72S12 14-160 VDC 12 VDC 0 mA 16.7 A 50 mA 3086 mA 90 90 16700uF CHB200W12-72S15 14-160 VDC 15 VDC 0 mA 13.5 A 50 mA 3086 mA 90 89 13500uF CHB200W12-72S24 14-160 VDC 24 VDC 0 mA 8.4 A 50 mA 3156 mA 88 88 8000F CHB200W12-72S48 14-160 VDC 48 VDC 0 mA 4.2 A 50 mA 2121 mA 89 89 2200F NOTE: 1. Nominal Input Voltage 72 VDC 2. Measured at 110Vin 3. An External Input Capacitor 100uF for All Models are Recommended to Reduce Input Ripple Voltage 4. An External Electrolytic Capacitor at least 240uF connected between BUS and -Vin is necessary PART NUMBER Nominal Input Number of Nominal Output Remote On/Off Series Mounting Inserts Voltage Outputs Voltage Logic CHB200W12- II O XX L -Y (Option) 12: 12VDC M3x0.5 Mounting None: None: Positive Inserts 15: 15VDC CHB200W12 72: 72 VDC S: Single 24: 24VDC N: Negative -C: Clear Mounting Inserts (3.2mm DIA.) 48: 48VDC Part Number Example: CHB200W12-72S12N-C: Half Brick, 200W, 12:1 14-160Vdc Input, Single 12Vdc Output, Negative Logic, Clear Mounting Insert www.cincon.com 1 REVISION: V10 CHB200W12 Series TECHNICAL SPECIFICATIONS (All specifications are typical at nominal input, full load at 25C unless otherwise noted.) ABSOLUTE MAXIMUM RATINGS PARAMETER NOTES and CONDITIONS Device Min. Typ. Max. Units Input Voltage Continuous -0.3 160 V All dc Input Surge Voltage 100ms max. V All 180 dc Operating Case Temperature At the Center Part of Base Plate C All -40 100 Storage Temperature C All -55 125 INPUT CHARACTERISTICS PARAMETER NOTES and CONDITIONS Device Min. Typ. Max. Units Operating Input Voltage V All 14 72 160 dc Input Under Voltage Lockout Turn-On Voltage Threshold V All 12.5 13 13.5 dc Turn-Off Voltage Threshold V All 10.5 11 11.5 dc Lockout Hysteresis Voltage V All 2 dc Maximum Input Current V =16.5V, Full Load. A in All 15 No-Load Input Current V =72V, Io=0A mA in See Model Number Table Input Filter Pi filter. All 2 2 Inrush Current (I t) As per ETS300 132-2. A s All 0.1 Input Reflected Ripple Current P-P thru 12uH inductor, 5Hz to 20MHz. mA All 50 OUTPUT CHARACTERISTICS PARAMETER NOTES and CONDITIONS Device Min. Typ. Max. Units Voltage Set Point Accuracy V =72V, Full Load, Tc=25C % in All -1.0 +1.0 Output Voltage Regulation Load Regulation Full Load to No Load % All 0.2 Line Regulation V =High Line to Low Line, Full Load % in All 0.2 Temperature Coefficient Tc=-40C to 100C %/C All 0.02 Output Voltage Ripple and Noise (5Hz to 20MHz bandwidth) 12Vo 200 15Vo 200 Peak-to-Peak mV 24Vo 240 Full load, 10uF tantalum and 1.0uF ceramic 48Vo 240 capacitors (for Vo=48V: Full Load 10uF 12Vo 80 aluminum and 1uF ceramic capacitors). 15Vo 60 RMS. mV 24Vo 100 48Vo 100 V = 16.5 to 160V in See Model Number Table Output Current Range A V = 14 to 16.5V in See Model Number Table,Full Load 10S Over Current Protection <90% Vo % All 110 125 140 Short Circuit Protection Hiccup Mode. Auto Recovery. Continuous, Auto Recovery. All External Load Capacitance Full load (Constant resistive load) uF See Model Number Table Pomax rated power, I I Output Voltage Trim Range o o max All % -20 +15 Output Voltage Remote Sense Pomax rated power, I I o o max All % +15 Range % of nominal Vo Over Voltage Protection Limited Voltage, % of Nominal Vo All % 117 125 140 www.cincon.com 2 REVISION: V10