V15 SIPSMT10W-12 SERIES 10 AMP POL CONVERTERS FEATURES * Non-isolated POL Converter * SIP / SMT Package * Output Current 10AMP * Input Voltage Range 6.0-14VDC * Output Voltage Range 0.7525-5VDC * 300KHz Switching Frequency * High Efficiency to 95% * Over Temperature Protection * Continuous Short Circuit Protection * Remote ON/OFF Control * Output Voltage Sequencing * Power Good Signal * UL/C-UL60950 Certified INPUT CURRENT Efficiency MODEL INPUT OUTPUT OUTPUT NUMBER VOLTAGE VOLTAGE CURRENT (%) NO LOAD FULL LOAD 0.7525VDC 10A 40mA 762mA 82 1.2VDC 10A 40mA 1149mA 87 1.5VDC 10A 50mA 1404mA 89 SIP10W-12S05A 6.0 14VDC 1.8VDC 10A 50mA 1666mA 90 2.0VDC 10A 60mA 1832mA 91 SMT10W-12S05A 2.5VDC 10A 65mA 2264mA 92 3.3VDC 10A 75mA 2956mA 93 6.5 14VDC 5.0VDC 10A 95mA 4386mA 95 NOTE: Nominal Input Voltage 12VDC L1 Q1 Vo,set (V) Rtrim (K) +VIN +VO 0.7525 Open 1.2 22.46 R sense Q2 D1 C2 1.5 13.05 C1 +SENSE 1.8 9.024 2.0 7.417 2.5 5.009 3.3 3.122 COM COM 5.0 1.472 R1 PGood PWM IC Rt ERR AMP ON/OFF TRIM Table 1. External Resistor Values SEQ for programming output voltage R2 Figure 1. Simplified Schematic 1 V15 SPECIFICATIONS All Specifications Typical At Nominal Line, Full Load, and 25 Unless Otherwise Noted GENERAL SPECIFICATIONS: INPUT SPECIFICATIONS: Input Voltage Range ........ 12V ....... 6.0 14.0V Efficiency ...................................................... See Table 12V ......... 6.5 14.0V Isolation Voltage ............................................. Non-isolation Under Voltage Lock-out Power up . 5.0V typ. Switching Frequency ................................................... 300KHz typ. Power down ...... 4.0V typ. Over Temperature Protection .... 130 typ. Input Filter Type....Capacitive Operating Ambient Temperature Range ............ -40 to +85 Positive Remote on/off Control : Power De-rating Curve .... see Figure2, 3 Module ON ... Open Circuit or = Vin Storage Temperature Range .......................... -55 to +125 Module OFF ..... < 0.4 Vdc MTBF . MIL-STD-217F, GB, 25, Full Load 0.92Mhrs typ. Dimensions: OUTPUT SPECIFICATIONS: SIP Package: 2.00 x 0.510 x 0.327 inches (50.8 x 12.95 x 8.30 mm) Voltage Accuracy ........ 1.5% max. Transient Response: 25% Step Load Change .............. <200us SMT Package: 1.30 x 0.530 x 0.346 inches (33.0 x 13.46x 8.80 mm) Ripple and Noise, 20MHz BW (note 3) ........ 30mV rms max. Structure .... Non-potted With Open Frame Type 75mV pk-pk max. Weight .. 8.5g Temperature Coefficient ............................. 0.03%/C max. NOTE : Short Circuit Protection ............................. Continuous 1. Measured From High Line to Low Line, Vo,set=3.3Vdc 2. Measured From Full Load to Zero Load, Vo,set=3.3Vdc Line Regulation (note 1) ............ 0.2% max. 3. The output noise is measured with 10uf tantalum capacitor Load Regulation (note 2) .............. 0.5% max. External Trim Adj. Range (see Table1) . Vo=0.75 5.0Vdc and 1uf ceramic capacitor across output. Sequencing Slew Rate Capability (dV /dt) . 0.1 1.0V/msec SEQ 4. The Input Terminal Recommend to Parallel With 100uF Capacitor Sequencing Delay Time . 10msec min. ESR<100m to Reduce The Input Ripple Voltage Tracking Accuracy Power up: 200mV max., Power down: 400mV max. 5. Suffix N to the Model Number with Negative Logic Remote on/off Capacitive Load Low ESR ........ 8000uF max. Model ON..Open Circuit or < 0.4VDC Power Good Signal Asserted Logic High .. Vo=90%-110%Vo, nom Module OFF>+2.8VDC to Vin Start up time ...... 7ms typ. 6. Suffix P to the Model Number with Power Good function. Dimensions: SIP Packages SMT Packages Mechanical Specification All Dimensions In Inches (mm) Tolerances Inches: X.XX= 0.02 , X.XXX= 0.010 Millimeters: X.X= 0.5 , X.XX=0.25 Bottom View of Board 0.327 max 8.30 2.00 1.30 0.23 50.8 33.0 5.8 PIN CONNECTION 0.120 3.05 Pin FUNCTION 0.297 0.346 +Output max. 1 7.54 8.80 0.065 1 2 3 4 5 6 7 8 9 101112 2 +Output 0.190 1.65 4.83 0.025 3 +Sense 0.64 0.050 0.025 4 +Output 1.27 0.100 0.28 0.64 5 Common 2.54 7.1 SEQ COM +VO TRIM +SENSEPGOOD N0 Pin/PGOOD 6 (Option) 0.400 0.900 10.16 22.86 Common 7 +V Input 8 +VIN ON/OFF 1.1mm PLATED THROUGH HOLE +V Input 9 1.6mm PAD SIZE 0.048 10 Sequency 0.112 1.22 L1 INDUCTOR 2.84 11 Trim LAYOUT PATTERN 12 On/Off Control TOP VIEW Surface Mount Contact SIP10W-12S05A Vo=3.3V Derating Curve SMT10W-12S05A Vo=3.3V Derating Curve 12.0 12 10.0 10 8.0 8 6.0 0LFM 6 0LFM 100LFM 100LFM 4.0 4 200LFM 200LFM 300LFM 2.0 2 300LFM 0.0 0 20 30 40 50 60 70 80 90 100 20 30 40 50 60 70 80 90 100 Ambient Temperature(C) Ambient Temperature(C) Figure2. Typical Power De-rating for 12V IN Figure3. Typical Power De-rating for 12V IN 2 Output Current (A) 0.33 0.14 8.4 3.6 0.29 7.4 0.010 min 0.25 0.510 12.95 Output Current (A) 0.063 1.60 0.075 1.91 0.405 10.29 0.530 13.46