NA5743-AL XXXXY Document 1075 For Linear Technology Flyback Transformer LT8584 Developed for Linear Technology LT8584 Isolated Monolithic AEC + Q200 125C Active Cell Balancer Designed to operate at 140 kHz Rated for 7 12 Watts 1500 Vrms, one minute isolation between primary and secondary AEC-Q200 Grade 1 qualified (40C to +125C ambient) Core material Ferrite Terminations RoHS tin-silver over tin over nickel over phos bronze. Other terminations available at additional cost. Weight 3.9 4.2 g Ambient temperature 40C to +125C Maximum part temperature +165C (ambient + temp rise) Storage temperature Component: 40C to +165C Tape and reel packaging: 40C to +80C Resistance to soldering heat Max three 40 second reflows at +260C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 200 per 13 reel Plastic tape: 32 mm wide, 0.5 mm thick, 24 mm pocket spacing, 11.2 mm pocket depth PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787 PCB Washing.pdf. Input Inductance Inductance Leakage Output 4 2 3 DCR max (Ohms) 6 3 Part voltage at 0 A at Ipk inductance Turns ratio Ipk voltage 1 5 number (V) 10% (H) min (H) pri sec max (H) pri : sec (A) (V) NA5743-AL 2 8 4.0 3.6 0.012 0.500 0.116 1 : 4 7.0 30 80 1. When ordering, please specify packaging code: Dot above pin1 NA5743-ALD Packaging: D = 13 machine-ready reel. EIA-481 embossed plastic 0.450 max tape (200 parts per full reel). 11,43 B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ( 25 charge), use 0.004/0,10 code letter D instead. 0.041 1,05 0.600 2. Inductance is for the primary, measured at 150 kHz, 0.1 Vrms, 0 Adc. Internal code max 15,24 3. Ipk is peak primary current drawn at minimum input voltage. 4. DCR for the primary is measured with windings connected in parallel. 5. Leakage inductance is for the primary, measured with secondary pins 0.050 0.413 0.024 shorted. 1,27 0.080 0.460 10,50 0,60 6. Turns ratio is with the primary windings connected in parallel. 2,03 11,68 5 1 4 7. Electrical specifications at 25C. Refer to Doc 362 Soldering Surface Mount Components before soldering. 0.50 max 12,7 1 1 8 0.098 Recommended 2 5 0.098 2,50 2,50 Land Pattern Pri Sec inches Dimensions are in mm 4 8 3 Primary windings to be connected in parallel on PC board Document 1075 Revised 11/01/19X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Audio Transformers / Signal Transformers category: Click to view products by Coilcraft manufacturer: Other Similar products are found below : CX2041NLT MGPWT-00449-P PE-64961 H1302FNLT H5008FNL H5012FNL H5020FNLT H5077NLT H5079NLT H5084FNLT B78476A9558A003 1812WBT2-4 1879479-1 HX2260FNL HX5014FNL EX2024FNL FL1066 T1137NLT T3012NL PE-65812FNL PE- 65848FNLT H1174FNL H1302FNL H5015FNL H5019EFNL H5062FNLT CX2047LNL MGPWT-00059-P MGPWT-00266-P MGPWT- 00278-P MGPWT-00431-P TTC-100 TTC-143-H TTC-5032-1 BX1194WNLT HX1234NLT HX5008FNLT HX5019FNL HX5084NL 3- 1879385-5 TX1263NLT 4-1879391-0 T1142NL HX6101FNL HX5084FNL HX1148NL HX5020FNLT HX5014FNLT T1124NL 1879732-1