Surface Mount Silicon Bridge Rectifiers RS501-G thru RS507-G REVERSE VOLTAGE - 50 to 1000 Volts - : RoHS Device FORWARD CURRENT - 5.0 Amperes RS5 .188(4.8)x45 FEATURES - Plastic material used carries UL recognition 94V-0 .846(21.5) .886(22.5) .807(20.5) .825(21.0) - High surge current capability - Ideal for printed circuit board - Typical IR less than 1mA - Built-in printed board stand offs 1.00 .042(1.07) DIA - High temperature soldering guaranteed: MIN. (25.4) .038(0.97) 250 for 5 seconds .400 .300 .300 .365 .354 .285 .285 .345 (10.2) (7.6) (7.6) (9.3) (9.0) (7.2) (7.2) (8.8) .195(5.0) .295(7.5) .180(4.6) .256(6.5) 1.594(40.5) 1.550(39.4) Dimensions in inches and (milimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25 ambient temperature unless otherwise specified. resistive or inductive load at 50HZ or 60HZ. SYMBOL RS501 RS502 RS503 RS504 RS505 RS506 RS507 UNIT CHARACTERISTICS Maximum Recurrent Peak Reverse Voltage VRM 50 100 200 400 600 800 1000 V Maximum RMS Voltage VRMS 35 70 140 280 420 400 700 V Maximum DC Blocking Voltage VDC 50 100 200 400 600 800 1000 V Maximum Repetitive Peak Reverse Voltage (Note1) VRRM 100 190 300 600 900 1200 1500 V Maximum Average Forward Output Current IFAVM natuer cooling,TA=45 C-Load 3.3 R+L-Load I(A 4.0 A 2 2 on chassis=31in ,200cm ,TA=45 5.0 C-Load R+L-Load 6.0 30 Maximum Repetitive Peak Forward Surge Current IFSM APK A 250 Peak Forward Surge Current Single TJ=25 IFSM APK 200 Sine-Wave on Reated Load (JEDEC Method) TJ=150 2 312 I t Rating for Fusing TJ=25 2 2 I t A S (t<8.3ms) TJ=150 200 Maximum Series Resistance at VRMS 0.15 0.3 0.6 1.2 1.8 OHM Maximum Reservoir Capacitor 10000 5000 5000 2500 1000 uF Maximum Reverse Current at TJ=25 10.0 A IR Rated Repetitive Peak Voltage TJ=150 6.0 mA Maximum instantaneous Forward Drop VF 1.0 V per Element at 5.0A -55 to +125 Operating and Storage Temperature Range TJ,TSTG NOTES:1.Valid for each bridge element. Page 1 MDS0905007A Surface Mount Silicon Bridge Rectifiers RATINGS AND CHARACTERISTIC CURVES RS501-G thru RS507-G FIG.1-DERATING CURVE FOR FIG.2- DERATING CURVE FOR OUTPUT RECTIFIED CURRENT OUTPUT RECTIFIED CURRENT 5.0 6.0 RESISTIVE LOAD 5.0 4.0 RESISTIVE RESISTIVE LOAD 4.0 3.0 CAPACITIVE LOAD 3.0 2.0 2.0 LIMITING COOLING MEDIUM 1.0 TEMPERATURE TA AT NATURE COOLING WITHOUT HEATSINK 1.0 0 0 0 50 100 150 0 50 100 150 AMBIENT TEMPERATURE CASE TEMPERATURE FIG.3-TYPICAL INSTANTANEOUS FORWARD FIG.4-MAXIMUM NON-REPETITIVE PEAK CHARACTERISTIC PER BRIDGE ELEMENT FORWARD SURGE CURRENT 100 100 40 0.2 60 0.4 20 40 0.6 10 0.8 6.0 20 4.0 1 10 2.0 8 6 1.0 4 0.6 0.4 TA=45 TYPICAL CHARACTERISTIC 2 SINGLE SINE-WAVE LIMITING CHARACTERISTIC 0.2 JEDEC METHOD 150 25 0.1 0 2 46 10 20 40 60 100200 4001 10 20 401 24 6 10 20 40 1h 0.5 0.7 1.0 1.1 1.2 1.3 1.4 1.5 0.6 0.8 0.9 ms sec min INSTANTANEOUS FORWARD VOLTAGE,VOLTS TIME FIG.6-MEAN AVERAGE FORWARD CURRENT CASE TEMPERATURE 120 125 130135 FIG.5-MAXIMUM TOTAL BRIDGE POWER 16 DISSIPATION 14 16 5 RESISTIVE 14 12 LOAD 10 12 10 15 10 20 8 CAPACITIVE LOAD CAPACITIVE 8 6 LOAD 6 4 RESISTIVE LOAD THERMAL RESISTANCE, 4 CASE TO COOLINT 2 MEDIUM RUCA /W 2 100 120 140 160 20 40 60 80 0 2 4 6 8 0 9.0 10 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 AVERAGE FORWARD CURRENT AMBIENT TEMPERATURE AVERAGE FORWARD OUTPUT CURRENT,AMPERES MDS0905007A Page 2 FORWARD POWER DISSIPATION, INSTANTANEOUS FORWARD CURRENT, AVERAGE FORWARD CURRENT WATTS AMPERES AMPERES POWER DISSIPATION,WATTS PEAK FORWARD SURGE CURRENT, AVERAGE FORWARD CURRENT AMPERES AMPERES