FFFF EEEE DDDD CCCC BBBB AAAA c NOTES: 1. RECOMMENDED SOLDER INSTRUCTION SEE SHEET 2 n1,12 (9x) 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI ( 5 : 1 ) FOR 30 MINUTES AFTER SOLDERING 4. METALSHELL: ZINC DIE CAST min. 50in NICKEL PLATING over COPPER 5. INSULATORS: PBT GF UL 94 V-0, BLACK 6. O-RING: SILICONE PER ASTM D2000 70 SHORE A DDDD 7. RUBBER GASKET: TPE DDDD 8. SEALING COMPOUND: EPOXY RESIN UL 94 V-0 BLACK 9. CONTACTS: COPPER ALLOY PLATING (SEE PART NO): o PLEASE ADD 1 for 30in HARD GOLD over min. 50in NICKEL o PLEASE ADD 3 for 8in HARD GOLD over min. 50in NICKEL SOLDER CUP ACCEPTS CABLE AWG 20 10. HEXLOCKING SCREWS: STAINLESS STEEL 11. RECOMMENDED PANEL CUT-OUT ON SHEET 2 12. RECOMMENDED TORQUE FOR MOUNTING SCREW b 35Ncm (3.1 in.LB) / max.67Ncm (6 in.LB) 13. OPERATING TEMPERATURE: -40C to +105C) 14. CONNECTOR IS PART MARKED: 15-00057o CONEC ABC 0,25 + 8,23 - 0 0,3 + 39,4 b - 0 RUBBER GASKET +0,12 25 - 0,13 PLACED ON TOP SURFACE POS. 1 OF MALE INSULATOR 0,23 + 16,81 CC - 0,02 CC CC CC POS. 6 SEALING COMPOUND 15-00057o O-RING CONEC ABC BBBB BBBB 4-40 UNC SEE NOTE 14 c SW 4,8 4-40 UNC b AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. scale: 2:1 (5:1) tolerance material: see notes dim. in mm AAAA AAAA date name title: drawn 17.10.08 Petker D-SUB MALE appd. 22.10.08 Fischer 9pos. SOLDER CUP norm with hexlocking screw dwg no: 2 x c 5461 15.12.14 K.H. d-old DIN- 3 x b 3435 29.09.09 HS A3 RR RR 15K1A275 a Original sh:1/2 RoHS compliant rev. description date name part no: o (see note 9) 15-00057 FFFF EEEE DDDD CCCC BBBB AAAA 10 0,3 + 21,1 - 0 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 4,6 9,4 +0,12 +0,4 10,31 6 - - 0,18 0,3 +0,25 3,6 - 0 0,13 R3,4 FFFF EEEE DDDD CCCC BBBB AAAA Solder Instruction DDDD DDDD 1. Cable should be prepared for soldering. The cable/wires must be pretinned. 2. Insert cable/wire into solder cup. 3. Operate the soldering iron at 350C, 50 Watt max. and use a pencil tip. 4. Put tip to wire in solder cup. 5. After 1 second bring in solder. 6. Heat for 3 seconds longer. Do not heat contact more than 4 seconds in total. 7. Remove soldering iron. 8. Wait until solder gets rigid again. 9. Do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up. CC CC CC CC RECOMMENDED PANEL CUT-OUT 0,1 20,5 i 0,26 A B BBBB BBBB 0,26 i B 0,1 25 A scale: 5:1 tolerance material: see sheet 1 dim. in mm AAAA AAAA date name title: drawn 17.10.08 Petker PANEL CUT-OUT appd. 22.10.08 Fischer D-SUB MALE 9pos. SOLDER CUP norm with hexlocking screw dwg no: d-old DIN- A3 RR RR 15K1A275 a Original sh:2/2 rev. description date name part no: SEE SHEET 1 FFFF EEEE DDDD CCCC BBBB AAAA 1 1 0 0,05 (2x) n3,1 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 11,4 0,1