FFFF EEEE DDDD CCCC BBBB AAAA c NOTES: 1. RECOMMENDED SOLDER INSTRUCTION SEE SHEET 2 n1,16 (9x) 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI FOR 30 MINUTES AFTER SOLDERING ( 5 : 1 ) 4. METALSHELL: ZINC DIE CAST min. 50in NICKEL PLATING over COPPER 5. INSULATORS: PBT GF UL 94 V-0, BLACK 6. O-RING: SILICONE PER ASTM D2000 70 SHORE A 7. SEALING COMPOUND: EPOXY RESIN UL 94 V-0 BLACK DDDD DDDD 8. CONTACTS: COPPER ALLOY PLATING (SEE PART NO): o PLEASE ADD 1 for 30in HARD GOLD over min. 50in NICKEL o PLEASE ADD 3 for 8in HARD GOLD over min. 50in NICKEL SOLDER CUP ACCEPTS CABLE AWG 20 9. HEXLOCKING SCREWS: STAINLESS STEEL 10. RECOMMENDED PANEL CUT-OUT ON SHEET 2 11. RECOMMENDED TORQUE FOR MOUNTING SCREW b 35Ncm (3.1 in.LB) / max.67Ncm (6 in.LB) 12. OPERATING TEMPERATURE: -40C to +105C 13. CONNECTOR IS PART MARKED: 15-00061o CONEC ABC +0,02 0,3 + 8 39,4 b - 0,23 - 0 0,12 + 25 - 0,13 +0 16,46 - 0,25 CC CC CC CC SEALING COMPOUND O-RING 15-00061o CONEC ABC BBBB BBBB 4-40 UNC SEE NOTE 13 c SW 4,8 4-40 UNC b AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. scale: 2:1 (5:1) tolerance material: see notes dim. in mm AAAA AAAA date name title: drawn 17.10.08 Petker D-SUB FEMALE appd. 22.10.08 Fischer 9pos. SOLDER CUP norm with hexlocking screw dwg no: 2 x c 5461 15.12.14 K.H. d-old DIN- 3 x b 3425 29.09.09 HS A3 RR RR 15K1A279 a Original sh:1/2 RoHS compliant rev. description date name part no: o (see note 8) 15-00061 FFFF EEEE DDDD CCCC BBBB AAAA 10 +0,3 21,1 - 0 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 4,6 9,4 0,17 0,4 + + 6,13 10,34 - 0,08 - 0,3 0,25 + 3,6 - 0R3,4 0,13 FFFF EEEE DDDD CCCC BBBB AAAA DDDD DDDD Solder Instruction 1. Cable should be prepared for soldering. The cable/wires must be pretinned. 2. Insert cable/wire into solder cup. 3. Operate the soldering iron at 350C, 50 Watt max. and use a pencil tip. 4. Put tip to wire in solder cup. 5. After 1 second bring in solder. 6. Heat for 3 seconds longer. Do not heat contact more than 4 seconds in total. 7. Remove soldering iron. 8. Wait until solder gets rigid again. 9. Do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up. CC CC CC CC RECOMMENDED PANEL CUT-OUT 20,5 0,1 i 0,26 A B BBBB BBBB 0,26 i B 0,1 25 A scale: 5:1 tolerance material: see sheet 1 dim. in mm AAAA AAAA date name title: drawn 17.10.08 Petker PANEL CUT-OUT appd. 22.10.08 Fischer D-SUB FEMALE 9pos. SOLDER CUP norm with hexlocking screw dwg no: d-old DIN- A3 RR RR 15K1A279 sh:2/2 rev. description date name part no: SEE SHEET 1 FFFF EEEE DDDD CCCC BBBB AAAA 1 10 0,05 (2x) n3,1 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 0,1 11,4