FFFF EEEE DDDD CCCC BBBB AAAA d b NOTES: 1. RECOMMENDED SOLDER INSTRUCTION SEE SHEET 2 n1,04 (26x) 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI FOR 30 MINUTES AFTER SOLDERING 4. METALSHELL: ZINC DIE CAST min. 50in NICKEL PLATING over COPPER 5. INSULATORS: PBT GF UL 94 V-0 BLACK ( 5 : 1 ) DDDD DDDD 6. O-RING: SILICONE PER ASTM D2000 70 SHORE A 7. SEALING COMPOUND: EPOXY RESIN UL 94 V-0 BLACK 8. CONTACTS: COPPER ALLOY PLATING (SEE PART NO.): o PLEASE ADD 1 for 30in HARD GOLD over min. 50in NICKEL o PLEASE ADD 3 for 8in HARD GOLD over min. 50in NICKEL SOLDER CUP ACCEPTS CABLE AWG 22 9. HEXLOCKING SCREWS: STAINLESS STEEL 10. RECOMMENDED PANEL CUT-OUT ON SHEET 2 11. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max. 67Ncm (6 in.LB) 12. OPERATING TEMPERATURE: -40C to +105C c 13. CONNECTOR IS PART MARKED: 15-00070o CONEC ABC +0,3 c 47,7 - 0 0,02 + +0,13 8 - 0,23 33,32 - 0,12 +0 24,79 - 0,25 CCCC CCCC SEALING COMPOUND 15-00070o O-RING CONEC ABC BBBB BBBB 4-40 UNC b d SEE NOTE 13 SW 4,8 4-40 UNC c AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. scale: 2:1 (5:1) tolerance material: see notes dim. in mm AAAA AAAA date name title: drawn 08.09.08 Schmidt D-SUB HD FEMALE appd. 15.09.08 Fischer 26pos. SOLDER CUP norm with hexlocking screw 2 x d 5445 03.12.14 Lehm. dwg no: 3 x c 3435 01.10.09 HS d-old DIN- 3 x b 3129 26.09.08 Petker A3 RR RR 15K1A273 a Original sh: 1 RoHS compliant rev. description date name part no: 15-00070o (see note 8) b FFFF EEEE DDDD CCCC BBBB AAAA 10 0,3 + 21,1 - 0 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 4,6 9,4 +0,4 12 - 0,3 +0,17 +0,4 6,13 9,5 - 0,08 - 0,3 +0,25 3,6 - 0R3,4 0,13 FFFF EEEE DDDD CCCC BBBB AAAA DDDD DDDD b Solder Instruction 1. Cable should be prepared for soldering. The cable/wires must be pretinned. 2. Insert cable/wire into solder cup. 3. Operate the soldering iron at 350C, 50 Watt max . and use a pencil tip. 4. Put tip to wire in solder cup. 5. After 1 second bring in solder. 6. Heat for 3 seconds longer. Do not heat contact more than 4 seconds in total. 7. Remove soldering iron. 8. Wait until solder gets rigid again. 9. Do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up. CCCC CCCC b RECOMMENDED PANEL CUT-OUT 0,1 28,8 0,26 i A B BBBB BBBB 0,26 i B 33,32 0,1 A scale: 5:1 tolerance material: SEE SHEET 1 dim. in mm AAAA AAAA date name title: drawn 08.09.08 Schmidt RECOMMENDED PANEL CUT-OUT appd. 15.09.08 Fischer D-SUB HD FEMALE 26pos. SOLDER CUP norm with hexlocking screw dwg no: d-old DIN- 2 x b 3129 26.09.08 Petker A3 RR RR 15K1A273 a Original sh: 2 rev. description date name part no: SEE SHEET 1 FFFF EEEE DDDD CCCC BBBB AAAA 1 10 n3,1 0,05 (2x) THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 0,1 11,4