FFFF EEEE DDDD CCCC BBBB AAAA NOTES: 1. FOR WAVESOLDERING (SOLDER BATH TEMPERATURE 265C FOR 8 SEC. ( 5 : 1 ) AND SOLDER PREHEAT 150C FOR 180 SEC.) 0,3 0,3 4,74 6,35 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI FOR 30 MINUTES AFTER HIGH TEMPERATURE EXPOSURE 4. METALSHELL: ZINC DIE CAST min. 50in NICKEL PLATING over COPPER DDDD DDDD 5. INSULATORS: PBT GF UL 94 V-0 GREEN 6. O-RING: SILICONE PER ASTM D2000 70 SHORE A BLUE SEALING 7. SEALING COMPOUND: EPOXY RESIN UL 94 V-0 BLACK COMPOUND 8. SIGNAL CONTACTS: COPPER ALLOY PLATING (SEE PART NO.): 3,2 0,2 30in HARD GOLD over min. 50in NICKEL if 1o in PART NO. GOLD FLASH over NICKEL if 3o in PART NO. 9. HIGH POWER CONTACTS 20 A: COPPER ALLOY PLATING, MATING SIDE (SEE PART NO.): o PLEASE ADD 1 for 30in HARD GOLD over min. 50in NICKEL o PLEASE ADD 3 for GOLD FLASH over NICKEL PLATING, TERMINATION SIDE: 160-240in TIN over 80in NICKEL 10. METAL BRACKETS: ZINC DIE CAST 300in COPPER/40-120in NICKEL/120-200in TIN 11. WASHERS: COPPER ALLOY 80in NICKEL 12. P.C.B. SNAPS: COPPER ALLOY min. 200in TIN over 80in NICKEL PCB-HOLE: n3,1 0,1mm PCB THICKNESS 1,6mm 13. HEXLOCKING SCREWS: STAINLESS STEEL 14. P.C.B.-HOLE DRILLINGS and RECOMMENDED PANEL CUT-OUT ON SHEET 2 15. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max. 67Ncm (6 in.LB) 16. CONNECTOR IS PART MARKED: 15-00564o CONEC ABC (see note 9) +0,02 8 - 0,23 CCCC CCCC +0,3 61,4 - 0 47,04 0,13 +0 38,5 - 0,25 0,3 11 BBBB (4,65) BBBB METAL BRACKET PRESS FOR FIXING ON PCB O-RING 15-00564o CONEC ABC PCB-SNAP 4-40 UNC SEE NOTE 16 SW 4,8 4-40 UNC scale: 2:1 (5:1) tolerance material: SEE NOTES dim. in mm AAAA AAAA AT ALL TIMES WATER RESISTANT date name title: CONNECTORS NOT IN USE drawn 23.11.15 Lehmenkhler D-SUB COMBINATION FEMALE 90 SHOULD BE COVERED WITH appd. 24.11.15 Schmidt 9W4S A CONEC WATER RESISTANT CAP norm with metal bracket, snap and hexlocking screw OR WATER TIGHT HOOD. dwg no: d-old DIN- A3 RR RR 15K1A1820 a Original sh:1/2 RoHS compliant rev. description date name part no: 15-00564o (see note 9) FFFF EEEE DDDD CCCC BBBB AAAA 10 +0,3 21,1 - 0 9,4 4,6 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 0,4 + 13,05 - 0,3 0,4 + 10,21 - 0,3 +0,4 +0,17 ,25 +0 10,75 n0,6 0,05 (5x) 6,13 3,6 - 0,3 - 0,08 - 0 0,4 + 13,5 - 0,3 +0,4 12,45 - 0,3 n2,85 (4x)R3,4 0,13 FFFF EEEE DDDD CCCC BBBB AAAA P.C.B. HOLE DRILLINGS (P.C.B. TOP SIDE) DDDD DDDD 47,04 0,13 14,48 0,1 14,48 0,1 8,28 0,1 7,77 0,1 5,54 0,1 n3,1 0,1 (2x) 1 A1 0,1 + n1 (5x) n3,2 0,1 (4x) - 0 P.C.B. EDGE CCCC CCCC FRONTPANEL 4,14 0,1 6,91 0,1 0,1 9,68 RECOMMENDED PANEL CUT-OUT 42,5 0,1 i 0,26 A BBBB BBBB B i 0,26 B 47,04 0,1 A scale: 4:1 tolerance material: SEE SHEET 1 dim. in mm AAAA AAAA date name title: drawn 23.11.15 Lehmenkhler P.C.B. HOLE DRILLINGS appd. 24.11.15 Schmidt RECOMMENDED PANEL CUT-OUT norm D-SUB Combination Female 90 9W4S dwg no: d-old DIN- A3 RR RR 15K1A1820 a Original sh:2/2 rev. description date name part no: SEE SHEET 1 FFFF EEEE DDDD CCCC BBBB AAAA 1 10 2,84 0,1 6,31 0,1 n3,1 0,05 (2x) THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 8,55 0,1 11,4 0,1 6,85 10,75