F E D C B A AT ALL TIMES WATER RESISTANT n0,64 0,05 (15x) ( 5 : 1 ) CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. SEALING D D COMPOUND 0,3 + b 39,22 - 0,15 33,32 0,13 + 0 24,79 - 0,25 SEALING GASKET 0,02 + 8 - 0,23 b C C 15-00650o CONEC ABC 4-40 UNC SEE NOTE 13 SW 4,8 4-40 UNC B c B NOTES: 1. FOR WAVESOLDERING (SOLDER BATH TEMPERATURE 265C FOR 8 SEC. AND SOLDER PREHEAT 150C FOR 180 SEC.) 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI FOR 30 MINUTES AFTER SOLDERING 4. METALSHELL: ZINC DIE CAST min. 50in NICKEL PLATING over COPPER 5. INSULATORS: PBT GF UL 94 V-0 BLACK 6. SEALING GASKET: SILICONE BLUE 7. SEALING COMPOUND: EPOXY RESIN UL 94 V-0 BLACK 8. CONTACTS: COPPER ALLOY PLATING (SEE PART-NO.): o PLEASE ADD 1 for 30in HARD GOLD over min. 50in NICKEL o PLEASE ADD 3 for GOLD FLASH over NICKEL 9. REAR SPACER CLIPS: COPPER ALLOY min. 200in TIN over 80in NICKEL PCB-HOLE: n3,1 0,1mm PCB THICKNESS 1,6mm 10. HEXLOCKING SCREWS: STAINLESS STEEL 11. P.C.B. HOLE DRILLINGS and RECOMMENDED PANEL CUT-OUT ON SHEET 2 12. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max. 67Ncm (6 in.LB) 13. CONNECTOR IS PART MARKED: 15-00650o CONEC ABC (see note 8) scale: 2:1 (5:1) tolerance material: SEE NOTES dim. in mm A A date name title: drawn 06.10.14 Lehmenkhler D-SUB FEMALE appd. 26.01.15 Fischer 15pos. SOLDER PIN STRAIGHT norm with closed 4-40 UNC thread and rear spacer clip dwg no: 1 x c 5827 25.09.15 Unkrer d-old DIN- 2 x b 5800 04.09.15 M.H. A3 R 15K1A1549 a Original sh: 1 RoHS compliant rev. description date name part no: 15-00650o (see note 8) F E D C B A 10 0,3 + 12,8 - 0,15 4,6 9,4 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 0,4 + 5 8,9 - 0,3 0,4 + 11,85 +0,4 - 0,3 12,35 - 0,3 0,25 + 2,55 - 0 +0,17 5,78 - 0,08 0,13 R3,4 F E D C B A P.C.B. HOLE DRILLINGS ( P.C.B. TOP SIDE ) D D +0,13 33,32 - 0,12 9,6 0,1 6,86 0,1 4,11 0,1 n3,1 0,1 (2x) 1,37 0,1 1 +0,1 n1 (15x) 0,1 - 2,74 0 C C 5,49 0,1 8,23 0,1 RECOMMENDED PANEL CUT-OUT 0,1 28,8 i 0,26 A B B B i 0,26 B 33,32 0,1 A scale: 5:1 tolerance material: SEE SHEET 1 dim. in mm A A date name title: drawn 06.10.14 Lehmenkhler P.C.B. HOLE DRILLINGS appd. 26.01.15 Fischer RECOMMENDED PANEL CUT-OUT norm D-SUB FEMALE 15pos. SOLDER PIN STRAIGHT dwg no: d-old DIN- A3 R 15K1A1549 a Original sh: 2 rev. description date name part no: SEE SHEET 1 F E D C B A 1 10 n3,1 0,05 (2x) THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 1,42 0,1 0,1 11,4 2,84 0,1