F E D C B A +0,5 3,3 0,3 - 0,3 6,35 AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER ( 5 : 1 ) RESISTANT CAP OR WATER TIGHT HOOD. D D SEALING COMPOUND 0,3 + c 30,88 - 0,15 +0,12 25 - 0,13 +0 16,46 - 0,25 SEALING GASKET c +0,02 8 - 0,23 n0,6 0,05 (9x) C C PRESS FOR 0,2 3,2 METAL BRACKET FIXING ON PCB b PCB SNAP 15-00659o CONEC ABC 4-40 UNC SEE NOTE 15 b SW 4,8 4-40 UNC d b NOTES: B B 1. FOR WAVESOLDERING (SOLDER BATH TEMPERATURE 265C FOR 8 SEC. AND SOLDER PREHEAT 150C FOR 180 SEC.) 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI FOR 30 MINUTES AFTER HIGH TEMPERATURE EXPOSURE 4. METALSHELL: ZINC DIE CAST min. 50in NICKEL PLATING over COPPER 5. INSULATORS: PBT GF UL 94 V-0 BLACK 6. SEALING GASKET: SILICONE BLUE 7. SEALING COMPOUND: EPOXY RESIN UL 94 V-0 BLACK 8. CONTACTS: COPPER ALLOY PLATING (SEE PART NO.): o PLEASE ADD 1 for 30in HARD GOLD over min. 50in NICKEL o PLEASE ADD 3 for GOLD FLASH over NICKEL 9. METAL BRACKETS: ZINC DIE CAST 300in COPPER/40-120in NICKEL/120-200in TIN 10. WASHERS: COPPER ALLOY 80in NICKEL 11. HEXLOCKING SCREWS: STAINLESS STEEL 12. PCB-SNAPS: COPPER ALLOY min. 200in TIN over 80in NICKEL PCB-HOLE: n3,1 0,1mm PCB THICKNESS 1,6mm 13. P.C.B. HOLE DRILLINGS and RECOMMENDED PANEL CUT-OUT ON SHEET 2 14. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max. 67Ncm (6 in.LB) 15. CONNECTOR IS PART MARKED: 15-00659o CONEC ABC (see note 8) scale: 2:1 (5:1) tolerance material: SEE NOTES dim. in mm A A date name title: drawn 29.09.14 Lehmenkhler D-SUB FEMALE 90 appd. 26.01.15 Fischer 9pos. SOLDER PIN ANGLED d b norm with closed 4-40 UNC thread,metal bracket,snap 2 x d 5827 25.09.15 Unkrer dwg no: 2 x c 5800 04.09.15 M.H. d-old DIN- 4 x b 5793 02.09.2015 K.H. A3 R 15K1A1554 a Original sh: 1 RoHS compliant rev. description date name part no: 15-00659o (see note 8) F E D C B A 10 0,3 + 12,8 - 0,15 4,6 9,4 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH 0,4 DO NOT ALTER CAD DRAWING BY HAND + 9,6 - 0,3 0,4 + 13,85 - 0,3 +0,4 11,18 - 0,3 +0,4 8,34 - 0,3 +0,25 2,55 - 0 0,17 + 5,78 - 0,08R 4 0,13 3, F E D C B A P.C.B. HOLE DRILLINGS (P.C.B. TOP SIDE) 0,12 D + D 25 - 0,13 5,49 0,1 0,1 2,74 +0,1 n1 (9x) - 0 n3,1 0,1 (2x) 1 P.C.B. EDGE C C FRONTPANEL 1,37 0,1 4,11 0,1 RECOMMENDED PANEL CUT-OUT 20,5 0,1 i 0,26 A B B B 0,26 i B 25 0,1 A scale: 4:1 tolerance material: SEE SHEET 1 dim. in mm A A date name title: drawn 29.09.14 Lehmenkhler P.C.B. HOLE DRILLINGS appd. 26.01.15 Fischer RECOMMENDED PANEL CUT-OUT norm D-SUB Female 90 9pos. Solder pin angled dwg no: d-old DIN- A3 R 15K1A1554 a Original sh: 2 rev. description date name part no: SEE SHEET 1 F E D C B A 1 10 9,6 n3,1 0,05 (2x) 6,75 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 11,4 0,1 5,49 0,1 2,84 0,1