F E D C B A +0,5 3,3 6,35 0,3 - 0,3 AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD ( 5 : 1 ) BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. D D SEALING COMPOUND 0,3 + c 39,22 - 0,15 +0,13 33,32 - 0,12 0,05 + 24,79 - 0,2 SEALING GASKET c +0,02 8 - 0,23 0,05 n0,6 (15x) C C 0,2 3,2 PRESS FOR METAL BRACKET b FIXING ON PCB PCB SNAP 15-00660o CONEC ABC 4-40 UNC b SEE NOTE 15 SW 4,8 4-40 UNC b d NOTES: B B 1. FOR WAVESOLDERING (SOLDER BATH TEMPERATURE 265C FOR 8 SEC. AND SOLDER PREHEAT 150C FOR 180 SEC.) 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI FOR 30 MINUTES AFTER HIGH TEMPERATURE EXPOSURE 4. METALSHELL: ZINC DIE CAST min. 50in NICKEL PLATING over COPPER 5. INSULATORS: PBT GF UL 94 V-0 BLACK 6. SEALING GASKET: SILICONE BLUE 7. SEALING COMPOUND: EPOXY RESIN UL 94 V-0 BLACK 8. CONTACTS: COPPER ALLOY PLATING (SEE PART NO.): o PLEASE ADD 1 for 30in HARD GOLD over min. 50in NICKEL o PLEASE ADD 3 for GOLD FLASH over NICKEL 9. METAL BRACKETS: ZINC DIE CAST 300in COPPER/40-120in NICKEL/120-200in TIN 10. WASHERS: COPPER ALLOY 80in NICKEL 11. HEXLOCKING SCREWS: STAINLESS STEEL 12. PCB-SNAPS: COPPER ALLOY min. 200in TIN over 80in NICKEL PCB-HOLE: n3,1 0,1mm PCB THICKNESS 1,6mm 13. P.C.B. HOLE DRILLINGS and RECOMMENDED PANEL CUT-OUT ON SHEET 2 14. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max. 67Ncm (6 in.LB) 15. CONNECTOR IS PART MARKED: 15-00660o CONEC ABC (see note 8) scale: 2:1 (5:1) tolerance material: SEE NOTES dim. in mm A A date name title: drawn 26.09.14 Lehmenkhler D-SUB FEMALE 90 appd. 26.01.15 Fischer d 15pos. SOLDER PIN ANGLED b norm with closed 4-40 UNC thread,metal bracket,snap 2 x d 5827 25.09.15 Unkrer dwg no: 2 x c 5800 04.09.15 M.H. d-old DIN- 4 x b 5793 02.09.2015 K.H. A3 R 15K1A1555 a Original sh: 1 RoHS compliant rev. description date name part no: o (see note 8) 15-00660 F E D C B A 10 0,3 + 12,8 - 0,15 4,6 9,4 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 0,4 + 9,6 - 0,3 +0,4 13,85 - +0,4 0,3 11,18 - 0,3 0,4 + 8,34 - 0,3 +0,25 2,55 - 0 0,17 + 5,78 - 0,08 R3,4 0,13 F E D C B A P.C.B. HOLE DRILLINGS (P.C.B. TOP SIDE) +0,13 33,32 - 0,12 D D 9,6 0,1 6,86 0,1 4,11 0,1 1,37 0,1 +0,1 n3,1 0,1 (2x) n1 (15x) - 0 1 2,74 0,1 P.C.B. EDGE C C FRONTPANEL 5,49 0,1 8,23 0,1 RECOMMENDED PANEL CUT-OUT 28,8 0,1 i 0,26 A B B B 0,26 i B 33,32 0,1 A scale: 5:1 tolerance material: SEE SHEET 1 dim. in mm A A date name title: drawn 26.09.14 Lehmenkhler P.C.B. HOLE DRILLINGS appd. 26.01.15 Fischer RECOMMENDED PANEL CUT-OUT norm D-SUB Female 90 15pos. Solder pin angled dwg no: d-old DIN- A3 R 15K1A1555 a Original sh: 2 rev. description date name part no: SEE SHEET 1 F E D C B A 1 10 9,6 n3,1 0,05 (2x) 6,75 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 0,1 11,4 0,1 5,49 2,84 0,1