F E D C B A n2,7 (5x) CUSTOMER IS RESPONSIBLE FOR SEALING THE MOUNTING HOLES. THE OTHER PARTS OF THE CONNECTOR ARE CONSIDERED IP67, BUT THE OVERALL SEALING EFFECTIVENESS IS DEPENDENT ON THE CUSTOMER ( 5 : 1 ) SEALING THE MOUNTING HOLES / HARDWARE. D D SEALING COMPOUND 0,3 + 53,09 - 0,15 0,13 47,04 +0 38,5 - 0,25 b SEALING GASKET +0,02 8 C - C 0,23 15-00682o CONEC ABC 4-40 UNC SEE NOTE 13 SW 4,8 4-40 UNC b NOTES: B B 1. RECOMMENDED SOLDER INSTRUCTION SEE SHEET 2 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI FOR 30 MINUTES AFTER SOLDERING 4. METALSHELL: ZINC DIE CAST min. 50in NICKEL PLATING over COPPER 5. INSULATOR: PBT GF UL 94 V-0 6. EXTENSION: HIGH TEMPERATURE PLASTIC UL 94-V0 7. SEALING GASKET: SILICONE 8. SEALING COMPOUND: EPOXY 9. HIGH POWER CONTACTS 20A: COPPER ALLOY PLATING, MATING SIDE (SEE PART NO.): o PLEASE ADD 1 for 30in HARD GOLD over min. 50in NICKEL o PLEASE ADD 3 for GOLD FLASH over NICKEL PLATING, TERMINATION SIDE: GOLD FLASH over NICKEL SOLDER CUP ACCEPTS CABLE AWG 12-14 10. HEXLOCKING SCREWS: STAINLESS STEEL 11. RECOMMENDED PANEL CUT-OUT ON SHEET 2 12. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max. 67Ncm (6 in.LB) 13. CONNECTOR IS PART MARKED: 15-00682o CONEC ABC (see note 9) scale: 2:1 (5:1) tolerance material: SEE NOTES dim. in mm A A date name title: drawn15.09.2015 Lehmenkhler D-SUB COMBINATION FEMALE appd. 21.09.2015 Fischer 5W5S SOLDER CUP norm with open 4-40 UNC thread dwg no: d-old DIN- 2 x b 6417 26.06.2017 Unkrer A3 R 15K1A1664 a Original sh: 1 RoHS compliant rev. description date name part no: 15-00682o (see note 9) F E D C B A 10 +0,3 12,8 - 0,15 4,6 9,4 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND +0,4 17,8 - 0,3 +0,25 2,55 - 0 0,17 + 5,78 - 0,08R3,4 0,13 F E D C B A Solder Instruction D D 1. Cable should be prepared for soldering. The cable/wires must be pretinned. 2. Insert cable/wire into solder cup. 3. Operate the soldering iron at 350C, 100 Watt max. and use a pencil tip. 4. Apply some solder to the solder tip of the soldering iron. 5. Put tip to wire in solder cup. 6. After 1 second bring in solder. 7. Heat for 5 seconds longer. Do not heat contact more than 6 seconds in total. 8. Remove soldering iron. 9. Wait until solder gets rigid again. 10. Do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up. C C RECOMMENDED PANEL CUT-OUT 42,5 0,1 i 0,26 A B B B 0,26 i B 47,04 0,1 A scale: 4:1 tolerance material: SEE SHEET 1 dim. in mm A A date name title: drawn15.09.2015 Lehmenkhler RECOMMENDED PANEL CUT-OUT appd. 21.09.2015 Fischer D-SUB COMBINATION FEMALE 5W5S SOLDER CUP norm with open 4-40 UNC thread dwg no: d-old DIN- A3 R 15K1A1664 a Original sh: 2 rev. description date name part no: SEE SHEET 1 F E D C B A 1 10 0,05 n3,1 (2x) THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 11,4 0,1