F E D C B A AT ALL TIMES WATER RESISTANT ( 5 : 1 ) CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER SEALING RESISTANT CAP OR WATER TIGHT HOOD. COMPOUND D D +0,3 30,88 - 0,15 0,12 + 25 - 0,13 b +0 16,46 SEALING - 0,25 GASKET +0,02 8 - 0,23 C C n2,85 (2x) 15-00706o CONEC ABC 4-40 UNC SEE NOTE 14 SW 4,8 4-40 UNC b NOTES: 1. FOR WAVESOLDERING (SOLDER BATH TEMPERATURE 265C FOR 8 SEC. AND SOLDER PREHEAT 150C FOR 180 SEC.) 2. IP RATING: IP 67 B B 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI FOR 30 MINUTES AFTER SOLDERING 4. METALSHELL: ZINC DIE CAST min. 50in NICKEL PLATING over COPPER 5. INSULATOR: PBT GF UL 94 V-0 6. EXTENSION: HIGH TEMPERATURE PLASTIC UL 94-V0 7. SEALING GASKET: SILICONE 8. SEALING COMPOUND: EPOXY RESIN UL 94 V-0 9. HIGH POWER CONTACTS 20A: COPPER ALLOY PLATING, MATING SIDE (SEE PART NO.): o PLEASE ADD 1 for 30in HARD GOLD over min. 50in NICKEL o PLEASE ADD 3 for GOLD FLASH over NICKEL PLATING, TERMINATION SIDE: 160-240in TIN over min. 80in NICKEL MALE CONTACT ON POS. A1 FEMALE CONTACT ON POS. A2 10. REAR SPACER CLIPS: COPPER ALLOY min. 200in TIN over 80in NICKEL PCB-HOLE: n3.1 0.1 PCB-THICKNESS 1.6mm 11. HEXLOCKING SCREWS: STAINLESS STEEL 12. P.C.B. HOLE DRILLINGS and RECOMMENDED PANEL CUT-OUT ON SHEET 2 13. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max. 67Ncm (6 in.LB) 14. CONNECTOR IS PART MARKED: 15-00706o CONEC ABC (see note 9) scale: 2:1 (5:1) tolerance material: SEE NOTES dim. in mm A A date name title: drawn 02.10.15 Lehmenkhler D-SUB COMBINATION FEMALE appd. 07.01.16 Fischer 2W2CS SOLDER PIN STRAIGHT norm with closed 4-40 UNC thread and rear spacer clip dwg no: d-old DIN- 2 x b 6417 02.03.2017 Lehm. A3 R 15K1A1713 a Original sh: 1 RoHS compliant rev. description date name part no: 15-00706o (see note 9) F E D C B A 10 0,3 + 12,8 - 0,15 4,6 9,4 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. +0,4 8,95 OWNERSHIP AND COPYRIGHT OF CONEC GmbH - 0,3 DO NOT ALTER CAD DRAWING BY HAND 0,4 + 11,85 - 0,3 +0,4 11,2 - 0,3 ,25 +0 2,55 - 0 17 +0, 5,78 - 0,08R ,4 0,13 3 F E D C B A P.C.B. HOLE DRILLINGS (P.C.B. TOP SIDE) D D 0,12 + 25 - 0,13 0,1 n3,1 (2x) 3,43 0,1 A1 n3,2 0,1 (2x) C C RECOMMENDED PANEL CUT-OUT 0,1 20,5 i 0,26 A B B B 0,26 i B 0,1 25 A scale: 4:1 tolerance material: SEE SHEET 1 dim. in mm A A date name title: drawn 02.10.15 Lehmenkhler P.C.B. HOLE DRILLINGS appd. 07.01.16 Fischer RECOMMENDED PANEL CUT-OUT norm D-SUB COMBINATION FEMALE 2W2CS SOLDER PIN dwg no: d-old DIN- A3 R 15K1A1713 a Original sh: 2 rev. description date name part no: SEE SHEET 1 F E D C B A 1 10 n3,1 0,05 (2x) THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 11,4 0,1