F E D C B A AT ALL TIMES WATER RESISTANT ( 5 : 1 ) CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. SEALING D D COMPOUND +0,3 53,09 - 0,15 47,04 0,13 b +0 38,5 - 0,25 SEALING GASKET +0,02 8 - 0,23 C C n0,65 (44x) 15-00757o CONEC ABC 4-40 UNC SEE NOTE 13 SW 4,8 4-40 UNC B B b NOTES: 1. FOR WAVESOLDERING (SOLDER BATH TEMPERATURE 265C FOR 8 SEC. AND SOLDER PREHEAT 150C FOR 180 SEC.) 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI FOR 30 MINUTES AFTER SOLDERING 4. METALSHELL: ZINC DIE CAST min. 50in NICKEL PLATING over COPPER 5. INSULATORS: PBT GF UL 94 V-0 6. SEALING GASKET: SILICONE 7. SEALING COMPOUND: EPOXY 8. CONTACTS: COPPER ALLOY PLATING (SEE PART-NO.): o PLEASE ADD 1 for 30in HARD GOLD over min. 50in NICKEL o PLEASE ADD 3 for GOLD FLASH over NICKEL 9. REAR SPACER CLIPS: COPPER ALLOY min. 200in TIN over 80in NICKEL PCB-HOLE: n3,1 0,1mm PCB THICKNESS 1,6mm 10. HEXLOCKING SCREWS: STAINLESS STEEL 11. P.C.B. HOLE DRILLINGS and RECOMMENDED PANEL CUT-OUT ON SHEET 2 12. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max. 67Ncm (6 in.LB) 13. CONNECTOR IS PART MARKED: 15-00757o CONEC ABC (see note 8) scale: 2:1 (5:1) tolerance material: SEE NOTES dim. in mm A A date name title: drawn 06.10.2015 Heinrich D-SUB FEMALE HD appd. 17.12.2015 Fischer 44pos. SOLDER PIN STRAIGHT norm with closed 4-40 UNC thread and rear spacer clip dwg no: d-old DIN- 2 x b 6417 06.04.2017 Unkrer A3 R 15K1A1682 a Original sh: 1 RoHS compliant rev. description date name part no: 15-00757o (see note 8) F E D C B A +0,3 12,8 - 0,15 4,6 9,4 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 0,4 0,4 + + 12,48 8,95 - 0,3 - 0,3 +0,4 +0,25 11,85 2,55 - 0,3 - 0 0,17 + 5,78 - 0,08 0,13 R3,4 F E D C B A P.C.B. HOLE DRILLINGS D D ( P.C.B. TOP SIDE ) 0,05 33,147 2,286 0,1 16,637 0,1 6,883 0,3 3,1 0,1 (2x) 1,143 0,1 1 +0,1 n0,9 (44x) - 0 C C 0,13 47,04 RECOMMENDED PANEL CUT-OUT 42,5 0,1 i 0,26 A B B B i 0,26 B 0,1 47,04 A scale: 4:1 tolerance material: SEE SHEET 1 dim. in mm A A date name title: drawn 06.10.2015 Heinrich P.C.B HOLE DRILLINGS appd. 12.10.2015 Fischer RECOMMENDED PANEL CUT-OUT norm D-SUB FEMALE HD 44pos. SOLDER PIN STRAIGHT dwg no: d-old DIN- A3 R 15K1A1682 a Original sh: 2 rev. description date name part no: SEE SHEET 1 F E D C B A 1 10 n3,1 0,05 (2x) THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 1,98 0,1 11,4 0,1 0,1 1,98