FFFF EEEE DDDD CCCC BBBB AAAA NOTES: n1,8 (2x) 1. RECOMMENDED SOLDER INSTRUCTION SEE SHEET 2 2. METALSHELLS: COPPER ALLOY min. 315in TIN over 40-80in NICKEL 3. INSULATORS: PBT GF UL 94 V-0 GREEN 4. HIGH POWER CONTACTS 10A: COPPER ALLOY PLATING MATING AREA: GOLD FLASH over NICKEL PLATING TERMINATION SIDE: GOLD FLASH over NICKEL DDDD DDDD SOLDER CUP ACCEPTS CABLE AWG 16-20 MALE CONTACT ON POS. A1 FEMALE CONTACT ON POS. A2 ( 5 : 1 ) 5. THREADED INSERTS: COPPER ALLOY min 200in TIN over 80in NICKEL 6. COLLARS: COPPER ALLOY min. 200in TIN over 80in NICKEL 7. HEXLOCKING SCREWS: STAINLESS STEEL 8. FRAME: ZINC DIE CAST NICKEL PLATED SEALING 9. O-RING: SILICON BLUE COMPOUND 10. SEALING COMPOUND: PUR BLUE 11. RECOMMENDED PANEL CUT-OUT ON SHEET 2 12. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max.40Ncm (3.5 in.LB) 13. CONNECTOR IS PART MARKED: 602W2CSXX61B30X CONEC ABC AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. +0,3 CC CC CC CC 39,4 - 0 +0,02 8 - 0,23 0,12 + 25 - 0,13 0,05 + 16,41 - 0,2 BBBB BBBB 602W2CSXX61B30X O-RING CONEC ABC SEE NOTE 8 4-40 UNC SEE NOTE 13 4-40 UNC SW 4,8 scale: 2:1 (5:1) tolerance material: SEE NOTES dim. in mm AAAA AAAA date name title: drawn 06.01.12 Henneboel D-SUB COMBINATION FEMALE appd. 06.01.12 Fischer 2W2CS SOLDER CUP norm with threaded insert and hexlocking screw dwg no: d-old DIN- A3 RR RR 15K1A989 a Original sh: 1 Directive 2002/95/EC RoHS compliant rev. description date name part no: 602W2CSXX61B30X FFFF EEEE DDDD CCCC BBBB AAAA 10 0,3 + 21,1 - 0 4,6 9,4 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 0,25 + 3,6 - 0 0,17 +0,1 + 5,73 14,25 - 0,08 - 0,4 0,13 R3,4 FFFF EEEE DDDD CCCC BBBB AAAA Solder Instruction DDDD DDDD 1. Cable should be prepared for soldering. The cable/wires must be pretinned. 2. Insert cable/wire into solder cup. 3. Operate the soldering iron at 350C, 100 Watt max. and use a pencil tip. 4. Put tip to wire in solder cup. 5. After 1 second bring in solder. 6. Heat for 5 seconds longer. Do not heat contact more than 6 seconds in total. 7. Remove soldering iron. 8. Wait until solder gets rigid again. 9. Do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up. CC CC CC CC RECOMMENDED PANEL CUT OUT 0,1 20,5 i 0,26 A B BBBB BBBB i 0,26 B 0,1 25 A scale: 3:1 tolerance material: SEE SHEET 1 dim. in mm AAAA AAAA date name title: drawn 06.01.12 Henneboel PANEL CUT-OUT appd. 06.01.12 Fischer D-SUB FEMALE 2W2CS SOLDER CUP norm with threaded insert and hexlocking screw dwg no: d-old DIN- A3 RR RR 15K1A989 a Original sh: 2 rev. description date name part no: SEE SHEET 1 FFFF EEEE DDDD CCCC BBBB AAAA 1 10 3,1 0,05 (2x) THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 11,4 0,1