Type ULP, 2 and 3 mm Ultra Low Profile Aluminum Electrolytic Capacitor, 85 C High Energy Density, REACH Compliant At 2 and 3 mm thin, type ULP offers the highest energy density available in a low profile aluminum electrolytic. Its ideal for the lowest profile circuits where high capacitance is needed for bulk storage. Look to type ULP to replace arrays of SMT solid tantalum capacitors. Highlights - 2 or 3 mm profile - High energy density .4 J/cc - Replaces banks of solid tantalum chips - 3000 hr life 85 C without voltage derating Specifications Temperature Range 40 C to 85 C, at 100% rated voltage Surge Voltage 120% of the rated working Vdc Capacitance Range 500 F to 24,000 F Capacitance Tolerance 20% at 120 Hz and 25 C DC Leakage Current After a five minute application of the rated working voltage at +25 C : 0.001CV Moisture Resistance After 500 hours storage at +60C and 90% to 95% RH with or without load, the capacitor will meet the following limits: C = +20%/20% of the initial measured value. ESR the initial specified value DCL the initial specified value DC Life Test Apply rated DC working voltage at 85C for 3000 hours, and then stabilize them to +25C. Capacitors will meet the following limits: C = 20% of the initial measured value ESR the initial specified value DCL the initial specified value Shelf Life Test Shelf life is typically 5 to 10 years. Accelerated test: After 500 hours at 85C, capacitors will meet the initial limits after stabilization at 25C. Vibration MIL-STD-202, Meth. 204, Sine Swept, IEC 60068-2-6 Standard ULP: 10g Mounting: Vibration capability is dependent upon mounting restraint. To achieve the high vibration levels as published on right, additional mounting restraint is required. Low Temperature Characteristics Impedence Ratio Z-40 / Z+25 C 120 Hz 10 (4 Vdc - 10 Vdc) 4 (16 Vdc - 63 Vdc) Altitude 60,000 feet max CDM Cornell Dubilier 140 Technology Place Liberty, SC 29657 Phone: (864)843-2277 Fax: (864)843-3800 Type ULP, 2 and 3 mm Ultra Low Profile Aluminum Electrolytic Capacitor, 85 C Vibration Test Level The specimens, while deenergized or operating under the load conditions specified, shall be subjected to the vibration amplitude, frequency range, and duration specified for each case size. Amplitude The specimens shall be subjected to a simple harmonic motion having an amplitude of either 0.06-inch double amplitude (maximum total excursion) or peak level specified above, whichever is less. The tolerance on vibration amplitude shall be 10 percent. Frequency Range The vibration frequency shall be varied logarithmically between the approximate limits of 10 to 2,000 Hz. Sweep Time and Duration The entire frequency range of 10 to 2,000 Hz and return to 10 Hz shall be traversed in 20 minutes. This cycle shall be performed 12 times in each of three mutually perpendicular directions (total of 36 times), so that the motion shall be applied for a total period of approximately 12 hours. Interruptions are permitted provided the requirements for rate of change and test duration are met. Typical Weight Case DA - 17g, Case DB - 22g 2 2 Terminals Flexible printed circuit 16 Amps for 1 second Max ( t = 250 A s) Case Material Cu/Ni/Zn (nickel - silver) 2x 10.5mm1 31mm1 21mm 42mm 1.9mm 20mm1(F1) 42mm1(F2) 62mm A 1-9 = Negative 10,11 = NC Pin 1 2.2mm Max (DA Case) 12-20 = Positive 3.2mm Max (DB Case) Mating Connector (Molex 0522712079 or equivalent) DETAIL A SCALE 2 : 1 CDM Cornell Dubilier 140 Technology Place Liberty, SC 29657 Phone: (864)843-2277 Fax: (864)843-3800