Ordering information Three phase input type TAH -10 -683 -O TAH series 1 2 3 4 1Model Name 2Rated Current 3Line to ground capacitor code:See table 1.1. table1.1 Line to ground capacitor code Line to ground Leakage Current Code capacitor (Input 250/500V 60Hz) (nominal value) 683 2.5mA/5.0mA max 68000pF 4Options D:DIN rail installation type The dimensions change when the option is set. * Refer to External view. The terminal cover is retracted inside the unit DIN rail installation type is option Features of TAH series Ultra high-attenuation type of common mode noise from 10kHz to 1MHz - Three Phase 500 VAC - Quick and easy push-down terminal Just connect the wires, push down and tighten the screws with a screwdriver Specifications No. Items TAH-04-683 TAH-06-683 TAH-10-683 TAH-20-683 TAH-30-683 1 Rated Voltage V AC Three Phase 500 2 Rated Current A 4610 20 30 3 Test Voltage (Terminal-Mounting Plate) 2,000 VAC (Cutoff Current = 100mA), 1minute at room temperature and humidity 4 Isolation Resistance (Terminal-Mounting Plate) 500 VDC 100MW minute at room temperature and humidity 5 Leakage current 250/500V 60Hz 2.5mA/5.0mA max 6 Voltage drop 1.5V max 1.0V max 7 Safety agency approval temperatures -25 to +85C (Refer to Derating Curve) 8 Operating temperature -40 to +85 (Refer to Derating Curve) C 9 Operating humidity 20 to 95%RH (Non condensing) 10 Storage temperature/humidity -40 to +85C/20 to 95%RH (Non condensing) 2 11 Vibration 10 to 55Hz, 19.6m/s (2G), 3min. Period, 1hour each X, Y and Z axis 2 12 Impact 196.1m/s (20G), 11ms Once each X, Y and Z axis 13 Safety agency approvals UL1283, CSA C22.2 No.8 (C-UL) , DIN EN133200 VDE0565 Teil3-1, ENEC 14 Case size (without projection) /Mass 63X64X128 mm (WXHXD) /620g max (Option : -D refer to external view) Circuit Diagram Derating Curve Case LINE LOAD 100 1 4 80 2 5 60 40 3 6 20 0 -40 -30 -20 40 50 60 70 80 90 Noise CY Filter Ambient Temperature C CY CY : Line to ground capacitor : Mounting Plate I-12 Load Factor % TAC,TAH series External view This product is shipped in the following condition, because it is equipped with push-down terminals. 1The terminal cover is retracted inside the unit. 2The screws for connecting the terminals are held in the up right position. Standard Type 128 Mounting Plate (2.5) 50 0.5 118 Protection Earth Input 20 83.5 Terminal Output Terminal Name Plate Output Input Terminal Terminal Output Terminal Terminal cover 4-f5.5 7-M4 Terminal cover Mounting Hole Closed the terminal cover Tolerance : 1 Mass : 620g or less Mounting Plate : Iron (surface finishing:nickel plating) t=1.0 Case : PBT Dimensions in mm Terminal block screw tighting torque M4:1.6N-m (16.9kgf-cm) max DIN rail installation Type (11) Mounting Plate 10 108 (2.5) 50 Input 83.5 Terminal 20 Protection Earth Output Terminal Name Plate Output Terminal Input Terminal Output Terminal Terminal cover 7-M4 Terminal cover Closed the terminal cover Tolerance : 1 Mass : 620g or less Mounting Plate : Iron (surface finishing:nickel plating) t=1.0 Case : PBT Dimensions in mm Terminal block screw tighting torque M4:1.6N-m (16.9kgf-cm) max DIN rail Note when installing the noise lter on a DIN rail. DIN rail When the noise lter is grounded through the Name Plate DIN rail, the proper noise attenuation may not be achieved. Be sure to connect the protection earth (PE) of Noise the noise lter body to the earth. Filter I-13 19 19 (9) (2) 64 (2) 7 64 12 0.5 50 12 63 63