9104-05-11 Coto

9104 SERIES/HIGH VOLTAGE SIP REED RELAYS 9104 Series Hi Voltage SIP Reed Relays Molded SIP relays are the industry standard when high reliability and consistent performance are desired in a compact package. The 9104 Series adds high voltage switching capability and high voltage standoff capability to a SIP relay package. These high voltage, high performance relays are ideally suited for Automatic Test Equipment, Instrumentation, Battery Management, Solar and Process Control applications where voltage isolation is a key design requirement. 9104 Series Features u High voltage switching up to 1000 V u High dielectric strength (up to 4000 V DC) 11 u High Insulation Resistance 10 minimum u High reliability, hermetically sealed contacts for long life u High speed switching compared to electromechanical relays u Molded thermoset body on integral lead frame design u Optional Coil Suppression Diode protects coil drive circuits u Magnetic Shield reduces interaction u UL File E67117 - Contact factory for details u RoHS compliant DIMENSIONS in Inches (Millimeters) TOP VIEW PIN 1 .950 Max. (24.13) .154 Typ245 Max. (3.9) (6.22) .103 Typ. (2.6) .320 Max020 Typ. (8.13) .(.51) .120 35 1 7 (3.0) .125 .005 .018 Typ010 Typ. (3.17 .13 ) (.46) (.25) .300 .200 .300 (7.62) (5.08) (7.62) Ordering Information 9XXX-XX-XX Part Number General Options Model Number 0=No Diode 9104 2 1=Diode Coil Voltage Dielectric Contacts 05=5 volts 12=12 volts Strength (Min) Shield to Coil 1=2000/3000 3=3000/3000 4=4000/4000 08242018 tteell: (: (440011) 94) 9433..2266886 f6 faaxx: (: (440011) 94) 9422..090922002 9104 MODEL NUMBER Parameters Test Conditions Units 4 Pin SIP COIL SPECS. Nom. Coil Voltage VDC 5 12 5 12 Max. Coil Voltage VDC 6.5 15.0 6.5 15.0 Coil Resistance +/- 10%, 25 C 175 500 140 500 Operate Voltage Must Operate by VDC - Max. 3.75 9.0 3.75 9.0 Release Voltage Must Release by VDC - Min. 0.5 1.0 0.5 1.0 CONTACT RATINGS 3 Switching Voltage Max DC/Peak AC Resist. Volts 1000 Switching Current Max DC/Peak AC Resist. Amps 0.5 Carry Current Max DC/Peak AC Resist. Amps 1.3 Contact Rating Max DC/Peak AC Resist. Watts 10 1 6 Life Expectancy-Typical Signal Level 1.0V, 10mA x 10 Ops. 300 Static Contact 50mV, 10mA 0.150 Resistance (max. init.) Dynamic Contact 0.5V, 50mA 0.200 Resistance (max. init.) at 100 Hz, 1.5 msec RELAY SPECIFICATIONS Insulation Resistance Between all Isolated Pins 11 10 (minimum) at 100V, 25C, 40% RH Capacitance - Typical No Shield pF 1.0 Across Open Contacts Open Contact to Coil No Shield pF - 4 Dielectric Strength Between Contacts VDC/peak AC 2000 / 3000 4000 (minimum) Contacts/Shield to Coil VDC/peak AC 2000 / 3000 4000 Operate Time - At Nominal Coil Voltage, msec. 0.75 including bounce - Typical 30 Hz Square Wave Release Time - Typical msec. 0.5 1 To p V i e w : Dot stamped on top of relay refers to pin 1 location Grid = .1x.1 (2.54mm x 2.54mm) 3 5 Notes: 1 7 Consult factory for life expectancy at other switching loads. 2 Optional diode is connected to pin 3(+) and pin 5(-). Correct coil polarity must be observed. 3 Switch current limited to 1.0mA 1000V. 4 Dielectric Strength 9104-XX-1X 9104-XX-3X 9104-XX-4X VDC/peak AC 2000/3000 3000/3000 4000/4000 Environmental Ratings: + + Storage Temp: -35C to 100C Operating Temp: -20C to 85C Solder Temp: 270C max 10 sec. max All electrical parameters measured at 25C unless otherwise specified. Vibration: 20 Gs to 2000 Hz Shock: 50 Gs 08242018 FForor m moostst re recceenntt d daattaa vis visitit w wwwww.c.cotoreotorellaayy.c.comom CCOOTTO TO TEECCHHNNOOLLOGOGYY, I, INCNC..