Series 09VR 9mm Panel Potentiometer Miniature 9 mm package size Rotational life (5,000 cycles) Wide temperature range (-10C to +70C) Mechanical travel options (280 and 300) Variety of standard resistances and tapers Applications Consumer portable electronics Commercial appliances Instrument amplifiers and guitar effects Keyboards and synthesizers Communications equipment Ordering Information Terminal Shaft Shaft Mechanical Detent Resistance Resistance Series Element Configuration Length Trim Travel Option Code Taper Ordering Information 09VR 1 B 20 F 2 N 103 B1 Code Spec. Code Spec. Code Spec.** Horizontal/Side Mount A2 10% Log N No Detent B Bushingless, PC Pins, C Center Detent A3 15% Log 6.5mm Height B1 linear Code Spec. Horizontal/Side Mount Knurled C3 15% Antilog M Sleeve Bushing, PC Pins, B (18 teeth) 6.5mm Height F Flatted Horizontal/Side Mount Knurled S Thread Bushing, PC Pins, L (40 teeth) 6.5mm Height Vertical/Rear Mount H Thread Bushing, PC Pins Code Spec. Vertical/Rear Mount Code Spec. K Sleeve Bushing, PC Pins 502 5k 1 280 103 10k Vertical/Rear Mount 2 300 U Bushingless, PC Pins 203 20k 503 50k Code Spec. 104 100k Code Spec.* 1 Single 254 250k 15 15 mm 504 500k 20 20 mm 25 25 mm 30 30 mm * See shaft trim options for available lengths. ** Other JIS tapers are available. See charts. 2019-04-16 Rev. A Page 1 of 7 2019 CTS Corporation. Information/product(s) subject to change. No warranty that product(s) will meet the stated specifications for customer specific applications or test equipment. Visit www.ctscorp.com for list of applicable patent(s), more information, or to request a quote. Series 09VR 9mm Panel Potentiometer Electrical Specifications Min Typical Max Unit Total Resistance Tolerance -20 +20 % Power Rating +0.05 watt Operating Voltage +20 VDC Residual Resistance +300 Slider Noise +100 mV Insulation Resistance 250 VDC for 1 min. +100 M Dielectric Strength 250 VAC for 1 min. no arcing Taper Linear and audio options (see charts) Mechanical 280 5 Total Mechanical Travel 300 5 Operating Torque 10 to 80 gf-cm Starting Torque 100 gf-cm max. Shaft Wobble Bushingless 0.8 x L/20mm p-p max. L = Shaft Length With Bushing 0.5 x L/20mm p-p max. L = Shaft Length Shaft Push-Pull Strength 5 kgf for 3 sec. Stop Strength 3 kgf-cm min. Detent Position 280 travel 140 5 300 travel 150 5 Detent Torque 30 to 300 gf-cm Rotational Life 5,000 cycles Panel Nut Tightening Torque 6 kgf-cm IP Rating 40 Mounting Hardware One flat washer and one mounting hex nut supplied with bushing option Packaging Bulk Weight 2 grams Environmental Min Typical Max Unit Operating Temperature -10 +70 C Storage Temperature -30 +70 C Soldering Conditions Wave Solder Preheat: 100C max for 2 min max Solder temperature: 260C 5C for 5 sec max. No clean foam flux recommended Manual Solder 350C 5C for 3 sec max. Sn95Ag5 no clean solder Wash Not recommended Moisture Sensitivity Level 1 ESD Classification (HBM) Not applicable All testing is performed at room ambient conditions except as noted. Users should verify device actual performance in their specific applications . This product is compliant to RoHS3 Directive 2015/863 Amendments of Annex II on 31 March 2015, and REACH SVHC Directive EC 1907/2006 Amendments of Annex XIV & Annex XVII on 15 January 2018. Custom and value-added options available on request. Please contact your sales representative for additional information. 2019-04-16 Rev. A Page 2 of 7 2019 CTS Corporation. Information/product(s) subject to change. No warranty that product(s) will meet the stated specifications for customer specific applications or test equipment. Visit www.ctscorp.com for list of applicable patent(s), more information, or to request a quote.