115JP300C201B1 CTS

Series 115 Data Sheet Rotary Trimmer Electrocomponents IndustriaIndustriadustriadustriaaalall 19mm Diameter19mm Diameter19mm Diameter9mm Diameter9mm Diamete9mm Diameter 22222 WWWWWataatt att ttttt ttt WWWWWirewouirewourewoununnnnnnd Rotary TrimmeRotary Trimmemmerrrrrr Features Fully enclosed construction Four mounting styles Long rotational life Optional grounded or insulated rotor construction Incorporated fixed resistor available Available with nylon shaft RoHS compliant Electrical and Mechanical Specifications Resistor Adjustment Resistance Range 1 ohm through 20K ohms (linear taper) Standard: Cross slot provided in rotor for screwdriver adjustment. Resistance Tolerance Special: Molded nylon, screwdriver-slotted shafts which 20% , 10% , 5% are integral with rotor are available in many lengths in increments of 1/8 (3.2mm) up to a maximum Power Rating, Watts 2 watts 55C derated to no load 105C, of 2 (50.8mm) as required. mounted on steel panel Mounting Types Available 1.5 watts 55C derated to no load 105C, Printed circuit mounted: Type 115 P mounted on bakelite panel Twist tab mounted: Type 115 T Snap-in mounted: Type 116 E Voltage Rating Rivet ear mounted: Type 117 R Terminals to case (insulated types only) High pot test, one minute 900 VAC Terminal Information Operating maximum 500 VDC Grounded Construction The grounded construction is Across end terminals supplied without a center terminal and the contactor is Determined by resistance value and wattage rating connected to the case. This construction can be furnished Resistance Taper with one end terminal at either end of the resistance Standard: Linear taper element or with terminals at both ends of the element. Insulated Construction The contactor is insulated from the Incorporated Fixed Resistor base and connected to the center terminal on the insulated A fixed resistor can be incorporated in the Series 115 construction. This construction can be supplied with the at the end of CW or CCW rotation to a minimum of 15% center terminal and one end terminal at either end of the of the total resistance value. The rotation is shortened resistance element or with the center terminal and terminals by an amount proportional to the ratio of the fixed resistor at both ends of the resistance element. to the total resistance value. Rotational Angle Stop Strength 4 in-lb. (4.6 Kgf- cm) Total Rotation: 270 5 Rotational Torque 1/2 to 10 in-oz. (36 720 gf-cm) 1 - 3 2009 CTS Corporation. All rights reserved. Information subject to change. 9/13/09 CTS Electrocomponents www.ctscorp.com END OF LIFEmm Type 115P, P.C. Mounted DIMENSION: inch CENTER TERMINAL SUPPLIED WITH INSULATED CONTACT ARM CONSTRUCTION. OMITTED ON GROUNDED CONTACT ARM CONSTRUCTION. 20.570.05 45 45 .810.002 1.6 END C.W END C.C.W OPTIONAL TERMINAL POSITION .063 ROT. ROT. PARALLEL TO MTG. SURFACE 10.290.05 TERMINALS .405.002 1.98X0.41 MIN. MIN078X.016 1.27 1.27 7.95 .050 .050 .313 2.790.05 1.4 .110.002 .055 2.39 .094 6.35 9.40.05 1.4 .370.002 .250 .055 1.52 270 ROT. 2.790.05 .060 .110.002 40 40 6.73 9.78 1.6 SUGGESTED PANEL 2 CROSS 19.84 PIERCING .265 .385 .063 1.6 SLOTS 1.57X4.72 .781 16.51 .063 .062X.186 .650 18.26 6.73 5.16 8.33 6.76 .719 .265 .203 .328 .266 9.78 11.51 .453 .385 MOUNTING SURFACE mm DIMENSION: Type 115T, Twist Tab Mounted inch CENTER TERMINAL SUPPLIED WITH INSULATED CONTACT ARM CONSTRUCTION. OMITTED ON GROUNDED CONTACT ARM CONSTRUCTION. 45 45 1.6 END C.W END C.C.W OPTIONAL TERMINAL POSITION .063 ROT. ROT. PARALLEL TO MTG. SURFACE 10.41 10.41 1.57 1.57 .062 .410 .410 .062 TERMINALS 1.98X0.41 2.08 .078X.016 .082 7.95 .313 4.17 .164 9.40.05 .370.002 1.4 1.52 .055 19.84 6.35 .060 3.96 2.790.05 .156 .781 .250 40 40 .110.002 270 ROT. SUGGESTED PANEL PIERCING 5.56 1.6 10.31 2 CROSS 23.010.38 .219 .406 .063 1.6 SLOTS 1.57X4.72 .906.015 .063 7.92 .062X.186 .312 15.88 6.35 7.92 3.96 5.56 .625 .250 .156 .312 .219 18.26 .719 MOUNTING SURFACE 11.91 10.31 .406 .469 PRINTED CIRCUIT BOARD mm Type 116E,Snap-in Ear Mounted DIMENSION: inch CENTER TERMINAL SUPPLIED WITH INSULATED CONTACT ARM CONSTRUCTION. OMITTED ON GROUNDED CONTACT ARM CONSTRUCTION. 20.220.05 45 45 .796.002 1.6 END C.W END C.C.W OPTIONAL TERMINAL POSITION 10.110.05 .063 PARALLEL TO MTG. SURFACE ROT. ROT398.002 TERMINALS MIN. 1.98X0.41 1.57 1.57 MIN. 1.4 2.790.05 .062 .078X.016 .062 .055 .110.002 7.95 .313 9.40.05 1.4 2.39 .370.002 .055 1.52 .094 2.790.05 .060 6.35 .110.002 .250 40 40 270 ROT. SUGGESTED PANEL PIERCING 6.35 9.93 1.6 2 CROSS .250 .391 .063 21.59 1.6 SLOTS 1.57X4.72 .850 8.33 .063 .062X.186 .328 16.28 6.76 4.78 8.33 .641 6.35 .266 .188 .328 .250 18.26 .719 MOUNTING SURFACE 11.51 9.93 .453 .391 PRINTED CIRCUIT BOARD 2 - 3 2009 CTS Corporation. All rights reserved. Information subject to change. 09/13/09 CTS Electrocomponents www.ctscorp.com END OF LIFE