06AK2 Delta

V D E SERIES POWER ENTRY MODULE EMI FILTERS INTRODUCTIONS SPECIFICATIONS 1. Power module incorporates an IEC connector, a fuse holder with 1. Maximum leakage current each optional power on/off switch and voltage selector switch, plus line-to-ground 115VAC 60Hz: 0.25mA an EMI filter all-in-one single, easy-to-install unit. 250VAC 50Hz: 0.45mA 2. Fuse holder designed for one IEC 5x20mm fuse. Safety interlock 2. Hipot rating (one minute) prevents fuse removal with line plug inserted (Use only with 250V line-to-ground: 2250VDC fuse). line-to-line: 1450VDC 3. All part numbers are UL recognized, CSA certified and VDE 3. Operating frequency: 50/60Hz approved. 4. Rated voltage: 115/250VAC 4. Switch electrical lifetime: 10,000 cycles. Maximum inrush current: 70A. MINIMUM INSERTION LOSS IN dB COMMON MODE (L-G) IN 50 OHM SYSTEM CURRENT FREQUENCY-MHz RATING .15 .50 1.0 5.0 10 30 3A 30 35 40 35 35 35 6A 16 25 30 42 45 40 DIFFERENTIAL MODE (L-L) IN 50 OHM SYSTEM 3A 10 40 45 45 45 35 6A 6 25 30 42 45 40 TYPE & RATED CURRENT DELTA PART NO. AK1 AK2 AK2D AK3 AK3D AK4 AK5 115VAC 6A 6A 6A 6A 6A 6A 6A RATED CURRENT 250VAC 6A 6A 4A 6A 4A 6A 6A IEC CONNECTOR FUSE HOLDER 12 12 POWER SWITCH SP DP SP DP 33 3 4 VOLTAGE SELECTOR SW REAR REAR REAR FRONT ELECTRICAL SCHEMATIC FIG. A FIG. A FIG. B FIG. A FIG. B FIG. A FIG. C 1. Single-pole UL, CSA & VDE approved 3. Voltage selector SW -UL, CSA & VDE approved Current rating: UL & CSA-6A both at 125VAC & 250VAC Current rating: 10A at 125VAC 5A at 250VAC. VDE-6A at 250VAC. 4. Voltage selector SW -UL, CSA & VDE approved 2. Double-pole UL CSA & VDE approved Current rating: UL & CSA-6A both at 125VAC & 250VAC Current rating: UL & CSA-6A at 125VAC, 4A at 250VAC VDE-6A at 250VAC. VDE-4A at 250VAC. ELECTRICAL SCHEMATIC AK3/4 ONLY AK1/4 WITHOUT POWER SW F SW L SW 1 L L L Cy L 110V F Cy L 110V L R C1 C2 L O 2 C1 R I C2 O L I A L N 220V A N D D E Cy E N N Cy N 110V 3 N G G 220V 110V G G 4 FIG. C FIG. A AK3D ONLY For transformers with two separate windings F L SW L Cy L L C1 R C2 O I L A N D E Cy N N G G FIG. B 4-1 POWER ENTRY MODULE FILTERSR0.04Max. 1.0 Suggested thickness of mounting panel is from 0.04 to 0.07 inch 2.6 0.003 Suggested mounting cutout 66.0 MECHANICAL CONSTRUCTION L 1 2 G G N L 4 3 N 2.65 67.3 AK5 2.57 65.3 2.65 67.3 N G O G I N L L AK2,AK2D 2.57 65.3 2.65 67.3 O G I N L G AK3,AK3D AK4 (without power switch) 1.059 26.9 2.65 67.3 G N L G INCH 1.059 AK1 2.57 UNIT: 26.9 mm 65.3 4-2 POWER ENTRY MODULE FILTERS 2.24 2.38 56.9 60.5 2.17 1.15 2.17 1.15 55.1 29.2 29.2 55.1 2.24 1.15 2.60 1.15 56.9 29.2 66.0 29.2 115V 0.43 0.57 10.9 14.48 0.65 2.17 16.5 55.1 1.059 1.059 26.9 26.9 1.063 0.003 27.0 220 110