06AR1 Delta

V D E SERIES POWER ENTRY MODULE EMI FILTERS INTRODUCTIONS SPECIFICATIONS 1. AR series is designed as a high performance, two-stage filter for 1. Maximum leakage current each low impedance load with better noise attenuation than AK series line-to-ground 115VAC 60Hz: 0.25mA in low frequency applications such as switching power supplies. 250VAC 50Hz: 0.45mA 2. Fuse holder designed for one IEC 5x20mm fuse. Safety interlock 2. Hipot rating (one minute) prevents fuse removal with line plug inserted (Use only with 250V line-to-ground: 2250VDC fuse). line-to-line: 1450VDC 3. All part numbers are UL recognized, CSA certified and VDE 3. Operating frequency: 50/60Hz approved. 4. Rated voltage: 115/250VAC 4. Switch electrical lifetime: 10,000 cycles. Maximum inrush current: 50A. COMPONENTS MINIMUM INSERTION LOSS IN dB COMMON MODE (L-G) IN 50 OHM SYSTEM PART NO. C1 (uF) L1 (mH) L2 (mH) Cy (pF) R ( ) 03AR1/2/3 0.1 1.5 9 CURRENT FREQUENCY-MHz 2200 1M 03AR2D/3D 0.033 9 1.5 RATING .15 .50 1.0 5.0 10 30 03AR 40 60 60 45 40 30 06AR1/2/3 0.1 0.7 2.5 06AR2D/3D 0.015 2.5 0.7 3300 2.2M 06AR 34 55 56 40 35 25 06AR4 0.1 0.7 2.5 06AR2D,3D 34 60 60 45 40 30 DIFFERENTIAL MODE (L-L) IN 50 OHM SYSTEM 03AR 6 45 55 50 45 40 06AR 5 25 60 50 45 35 06AR2D,3D 10 10 50 50 45 40 ELECTRICAL SCHEMATIC AR3/4 ONLY AR1/4 WITHOUT POWER SW L AR3D ONLY L L Cy F L L SW1 L C1 R C2 C3 Cy F L L SW1 C1 R C2 C3 I O I O L1 L2 L1 A L2 N N A E D N Cy D E N Cy N N G G G G FIG. B FIG. A C3:0.1uF C2:0.1uF TYPE & RATED CURRENT DELTA PART NO. AR1 AR2 AR2D AR3 AR3D AR4 115VAC 6A 6A 6A 6A 6A 6A RATED CURRENT 250VAC 6A 6A 4A 6A 4A 6A IEC CONNECTOR FUSE HOLDER 12 12 POWER SWITCH SP DP SP DP 33 3 VOLTAGE SELECTOR SW REAR REAR REAR ELECTRICAL SCHEMATIC FIG. A FIG. A FIG. B FIG. A FIG. B FIG. A 1. Single-pole UL, CSA & VDE approved, VDE-6A at 250VAC. 2. Double-pole UL, CSA & VDE approved, VDE-4A at 250VAC. Electrical lifetime: 10,000 cycles. Maximum inrush current: 50A. 3. Voltage selector SW -UL, CSA & VDE approved Current rating: 10A at 125VAC 5A at 250VAC. 4-3 POWER ENTRY MODULE FILTERSR0.04Max. 1.0 Suggested thickness of mounting panel is from 0.04 to 0.07 inch 2.6 0.003 suggest mounting cutout 66.0 2.65 67.3 MECHANICAL CONSTRUCTION O G I N L 2.57 65.3 N G L AR2, AR2D 2.65 67.3 O G I N L G AR3, AR3D AR4(without power switch) 1.059 26.9 2.65 67.3 G N L G AR1 2.57 1.059 65.3 26.9 INCH UNIT: mm 4-4 POWER ENTRY MODULE FILTERS 2.38 60.5 1.059 2.17 1.15 2.24 1.15 26.9 2.60 1.15 29.2 56.9 55.1 29.2 66.0 29.2 115V 2.17 55.1 0.65 16.5 1.063 0.003 27.0