E Description: 90P1 The 07590 premium series heel grounder provides effective ESD protection. The D cup is made from a black and non-marring rubber with inner tear resistant conductive scrim. The rubber is antistatic, low tribocharging, and dissipative. It removes charges when in contact with ESD protected floors. This foot grounder meets the less 6 than 3.5 x 10 ohm requirement of ANSI ESD S20.20. This unit includes either a one or two LISTED megohm molded external resistor, a conductive tab with carbon suffused fibers, and a D-ring fastening system. The product has been tested to ESD STM97.2 - Floor Materials and Footwear Voltage Measurement in Combination with a Person. It is a suitable ESD footwear component in 7 Flooring - Footwear System when used as the primary grounding method (<3.5 x 10 ohms per ESD STM 97.1 Floor Materials and Footwear-Resistance Measurement in Combination with a Person.) F Components: B A. 0.060 thick, 1.50 wide, black conductive exterior with a non-marring interior. Tear resistant nylon reinforced 4.3 oz. inner scrim layer prevents the rubber from tearing. B. 3/8 wide, 30 long blue polyester tab contains electrically conductive carbon suffused fibers. A C. 3/4 wide, blue loop material with return hook tip for quick and easy adjustment and wearer s comfort. D. 3/4 wide blue elastic material stretches for comfort. E. D-ring fastening system. F. A 1/4 watt, 1 megohm blue (07590) or 2 megohm black (07593) molded external resistor. listed for safety and date coded. Tab to cup resistance: 6 7 10 - 10 Ohms 100 volts ITEM DESCRIPTION 6 7 07590 Foot Ground, Heel, 1 megohm resistor, RTG: 10 - 10 Ohms 6 7 07593 Foot Ground, Heel, 2 megohm resistor, RTG: 10 - 10 Ohms Made in America Note: Two heel straps are recommended for reliable grounding and ESD protection, Our UL listed foot grounders are rated at 250 VAC. It is not recommended to use them where exposure providing ground when one foot is off the floor. to line voltages above 250 VAC is possible. Caution: The foot grounder is for ESD control. It will not Operator is grounded when foot is in contact with grounded dissipative or reduce or increase your risk of receiving electric shock when using or working on electrical equipment. conductive flooring. Desco recommends the use of foot ground tester item No. 19252, 19253, Meets the requirements of JEDEC-108/9, MIL-HDBK-263A, MIL-STD-1686, DOD-STD-2000. 98280/98273, or 98280/98254. For additional information on the use and maintenance of foot grounders please FOOT GROUND, HEEL, D-RING FASTENER ask for Technical Bulletins TB-2020, TB-2040, TB-3000. DESCO WEST: 3651 WALNUT AVE., CHINO, CA 91710 WEB SITE: www.desco.com DATE: PHONE (909) 627-8178 FAX (909) 627-7449 DRAWING NUMBER December DESCO EAST: ONE COLGATE WAY, CANTON, MA 02021-1407 07590 2008 PHONE (781) 821-8370 FAX (781) 575-0172 2008 DESCO INDUSTRIES INC. Employee OwnedX-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Antistatic Control Products category: Click to view products by Desco manufacturer: Other Similar products are found below : 13020 13490 13870 13879 13881 13883 13882 14404 2202SP 3039 37061 42470 09060 09857 42516 37059 04563 17252 19691 19695 09037 09826 09813 66070 100816 68101 68103 98132 73741 13868 13485 13457 13245 13468 13420 13332 13205 13135 91070 8031 8523 66085 40931 37081 13080 13215 13806 73749 010-0225 17260