515-1055F Dialight

3 x 5mm Rectangular Optopipe Optical Light Pipe, 4 Array (RJ45 Jack) 515-1055 FRONT MicroLED SMT LEDs PANEL 31.2 1.23 13.97 5.08 2.54 REF .550 .200 .100 for use with 515-1055 TYP (4) PLACES 27.43 3 PLCS 1.08 DIFFUSED PART NO. PAGE FRONT SURFACES 20.57 Recommended .81 3.05 11.43 .120 597-3xx1-1xx 1-19 .450 (4) PLACES C.L. LED 597-77x1-1xx 1-20 1.91 .075 Alternatives 1.57 6.99 .062 13.97 .275 597-3xxx-4xx 1-27 & 1-28 27.94 .550 7.62 1.10 .300 597-3xx1-4xx 1-28 C.L. MOUNTING PIN 1 33.53 597-3xx1-5xx 1-30 1.32 1.50 19.61 .059 .772 597-5x11-4xx 1-27 TYP 5.64 597-5202-4xx 1-27 .222 3.99 3.58 .157 .141 DIRECTION TYP TYP OF LIGHT NOTE: designed for .113 .002 .99 LED alternatives may not produce optimum light TYP 2 PLACES .039 post-reflow TYP PC board insertion. output 27.94 .08 8.33 1.100 .003 .328 Solder Pad/Holes layout shown is for bi-color 2.69 .106 Dimensions in mm inches LEDs listed under Recommended category TYP RECOMMENDED SOLDER PAD /HOLES LAYOUT Contact factory for other layouts Features High transmissivity polycarbonate material UL94V-0 compliance ESD protection (circuit isolation from front panel) Wide viewing angle Arrays reduce insertion costs Secures to PCB by snap-fit LED Data For absolute maximum ratings and other electrical and optical Operating/Storage Temperature data on the recommended LEDs, refer to LED data sheets. 30C to +100C Dialight Optopipe Light Pipe Description This Optopipe functions as a through-the-case indicator by conducting the light over the top of connectors or switch- es with a maximum height of 0.550 . It is equivalent to the 515-1022 and well suited to applications where vibration is a concern. This Optopipes four 3 x 5mm rectangular light emitting surfaces appear bright and are optically well isolated. The light pipe is reliably held in place by 2 snap-fit pins located next to the first and fourth light pipe elements. These pins pos- itively lock onto 0.062 thick PCBs regardless of individual variations in thickness. A textured finish on the 4 light emitting surfaces maximizes the viewing angle. The recommended light sources are Dialight s 597 Series PLCC-2 or PLCC-4 type SMT LEDs. The LEDs are mounted in a straight line on a 0.550 pitch. The light pipe material is water clear transmissive polycarbonate rated UL94-V0, and has a 35% oxygen index. Dialight can provide custom Optopipe solutions for your applications. Dialight Corporation 1501 Route 34 South Farmingdale, NJ 07727 TEL: (732) 919-3119 FAX: (732) 751-5778 www.dialight.comX-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for LED Light Pipes category: Click to view products by Dialight manufacturer: Other Similar products are found below : 1367627-1 SLP3-300-450-F SLP3-400-450-R LPA-C011301S-23 LPA-C011301S-6 LPF-C011306S FLP25-1.95 VLP-640-F LPA- C011301S-5.4 LPA-C041301S-2 LPA-R051171S-12 LPA-S011331S 515-1027-803F 515-1217F SLP3-150-300-R SLP3-500-450-R 515- 1064-810F FLPV-SG BDL-1187 7511A41 7511A87-500 FLPV-SBC 5151064802F 5151-192-0055-0DF LPF-R011340S 515-1166-801F FLPF-6.0 SLP3-350-200-F PM4-C1522-3.70 LC-11.25 CLP-1214 515-1064-808F FLX3 05 515-1192-0025-0DF 515-1192-80-3DF PBLP- 1001-1 LC2-4.1 LPC062CTP LSS024CTP LPC088CTP SLP3-150-300-F 2202312 515-1302-0500F RLP1-200-800 RLP1-400-500 LPA- C011301S-15 2202311 SLP3-150-450-R 7511A53 1270.1003