515-1061F Dialight

3mm Round Optopipe Optical Light Pipe, Bi-Level 515-1061 13.97 2.54 .55 4.57 Recommended .100 1.91 .18 .075 1.52 3.05 DIFFUSED FRONT REF .120 7.62 .06 SURFACES .300 2 PLCS MicroLED SMT LEDs 3.05 .120 TYP 5.08 9.14 2 PLCS .200 .36 1.57 for use with 515-1061 .062 2.54 .100 2.79 .11 1.63 .064 5.12 2.29 FRONT PART NO. COLOR PAGE MOUNTING .200 .090 PANEL .25 2.54 PIN .100 .010 THIS VIEW SHOWS TWO 515-1061 597-3111-5xx AlGaAs Red 1-30 5.12 LIGHT PIPES MOUNTED .200 SIDE BY SIDE 7.87 597-3211-5xx Orange 1-30 .310 597-3301-5xx Green 1-30 4.50 DIRECTION 1.45 DIRECTIO 4.50 .177 .057 1.04 OF LIGHT .177 OF LIGHT 2.69 TYP .041 TYP 597-3401-5xx Yellow 1-30 .106 3.35 TYP TYP .132 3.89 597-7701-5xx Red/Green 1-31 2.54 .05 1.60 .153 .100 .002 .063 TYP 597-7721-5xx Yellow/Green 1-31 1.52 .05 3.73 4.27 .060 .002 .060 .002 .147 .168 TYP, 2 PLCS TYP, 2 PLCS 2.54 .05 .100 .002 NOTE: designed for 4.39 4.39 post-reflow .173 .173 TYP PC board insertion. FIGURE A FIGURE B (USING SINGLE COLOR SMT LEDS) (USING BI-COLOR SMT LEDS) RECOMMENDED SOLDER PAD/HOLES LAYOUT RECOMMENDED SOLDER PAD/HOLES LAYOUT Dimensions in mm inches Features Can be mounted in arrays spaced .200 apart (min.) High transmissivity polycarbonate material UL94V-0 compliance LED Data ESD protection (circuit isolation from front panel) For absolute maximum ratings and other electri- Wide viewing angle cal and optical data on the recommended LEDs, Arrays reduce insertion costs refer to LED data sheets. Allows bi-level SMT indicators Operating/Storage Temperature Secures to PCB by press-fit 30C to +100C Dialight Optopipe Light Pipe Description This Optopipe is a standard design intended as a SMT compatible replacement for our 553 Series Circuit Board Indicators. The light outputs are spaced vertically .100 from the PCB to the first element, and then 0.200 between the top and bottom elements. We recommend a minimum of 0.200 between light pipes as a normal mounting pitch. This Optopipe is held in place by 2 press-fit pins along the bottom of the device. The light pipe is not attached to the panel at any point but can protrude through holes in the panel. The gently arcing emitting end sticks through the plastic or metal panel. The light source is Dialight s 597 Series Type 1208 LED. The light pipe material is water clear transmissive polycarbonate rated UL94-V0, and has a 35% oxygen index. Dialight can provide custom Optopipe solutions for your applications. Dialight Corporation 1501 Route 34 South Farmingdale, NJ 07727 TEL: (732) 919-3119 FAX: (732) 751-5778 www.dialight.comX-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for LED Light Pipes category: Click to view products by Dialight manufacturer: Other Similar products are found below : 1367627-1 SLP3-300-450-F SLP3-400-450-R LPA-C011301S-23 LPA-C011301S-6 LPF-C011306S FLP25-1.95 VLP-640-F LPA- C011301S-5.4 LPA-C041301S-2 LPA-R051171S-12 LPA-S011331S 515-1027-803F 515-1217F SLP3-150-300-R SLP3-500-450-R 515- 1064-810F FLPV-SG BDL-1187 7511A41 7511A87-500 FLPV-SBC 5151064802F 5151-192-0055-0DF LPF-R011340S 515-1166-801F FLPF-6.0 SLP3-350-200-F PM4-C1522-3.70 LC-11.25 CLP-1214 515-1064-808F FLX3 05 515-1192-0025-0DF 515-1192-80-3DF PBLP- 1001-1 LC2-4.1 LPC062CTP LSS024CTP LPC088CTP SLP3-150-300-F 2202312 515-1302-0500F RLP1-200-800 RLP1-400-500 LPA- C011301S-15 2202311 SLP3-150-450-R 7511A53 1270.1003