2mm LED CBI Circuit Board Indicator (DIN 41494 Compatible), Bi-Level 571-01xx HOUSING TYPE 0 HOUSING TYPE 1 WITHOUT PINS 13.72 1.52 .20 WITH PINS 2.54 .05 .060 .008 .540 2.50 .100 .002 5.08 5.08 1.37 .095 1.27 TYP (3) .20..0 .200 .054 .050 MAX 8.60 1.80 .20 .339 3.81 3.81 .071 .008 .150 .150 1.02 .05 .040 .002 0.38 2.54 2.54 TYP (4) .015 .100 .100 3.00 .25 0.38 RECOMMENDED PC BOARD .118 .010 .015 CATHODE HOLE PATTERN CATHODE 0.46 2.54 0.41 Except where noted Housing Type 1 .018 .100 .016 2.54 2.54 dimensions are the same as Housing Type 0 .100 TOP LED 4.83 .100 .190 Dimensions in mm inches PART NO. WITHOUT PINS COLOR* Features Designed to accommodate DIN 41494 571-0111 Red-Red Multiple CBIs form horizontal LED arrays on 2.54mm 571-0112 Red-Green (0.100) center-lines 571-0122 Green-Green High Contrast, UL 94 V-0 rated, black housing 571-0132 Yellow-Green Oxygen index: 32% 571-0133 Yellow-Yellow Polymer content: PBT, 0.290 g * Top-Bottom LED Housing stand-offs facilitate PCB cleaning PART NO. WITH PINS COLOR* Solderability per MIL-STD-202F, method 208F 571-0111-100 Red-Red LEDs are safe for direct viewing per IEC 825-1, EN-60825-1 571-0112-100 Red-Green 571-0122-100 Green-Green Tolerance note: As noted, otherwise: 571-0132-100 Yellow-Green LED Protrusion: 0.04 mm 0.016 571-0133-100 Yellow-Yellow CBI Housing: 0.02mm 0.008 * Top-Bottom LED Arrays available. See Part Number ordering code. PART NUMBER ORDERING CODE Series Top LED Color Array Code Custom Combinations Contact factory for information on custom color combinations. 5 7 1 0 1 x x 1 0 x EXAMPLE LED Type Bottom LED Number of Single unit with pins Color 1) With pins Bi-Levels in array LED colors: 0) Blank, 1) Red, 2) Green, 3) Yellow 1 0 0 10x Suffix required only when ordering single 5 7 1 0 1 x x units with pins or arrays 1 0 2 Two bi-levels in an array (4 LEDs) See LED data sheet for additional information Typical Operating Characteristics (T = 25C) A See Page 3-17 and 3-18 for Reference Only LED Drive Circuit Examples GENERAL PURPOSE See Page 3-20 for Pin Out Peak I * V ** Viewing LED V F 1 Part Number Color Wavelength nm mcd Volts Angle 2 /2 Data sheet Page Red 635 12.6 2 38 521-9630 3-13 571-01xx Green 565 8.7 2.1 38 521-9632 3-13 Yellow 585 12.6 2.1 38 521-9631 3-13 * I = 10mA ** I = 20mA F F Dialight Corporation 1501 Route 34 South Farmingdale, NJ 07727 TEL: (732) 919-3119 FAX: (732) 751-5778 www.dialight.co m 3-102mm Discrete LED Diffused 521-9630, -9631, -9632 CATHODE I.D. 2.40 PART NO. COLOR .40 .095 2.90 25.40 .016 .114 1.00 MIN 1.00 TYP 521-9630 Red .04 CATHODE MIN 521-9631 Yellow .45 3.30 2.54 1.80 .018 .13 .10 .071 TYP NOM 521-9632 Green 1.52 .060 1.50 .059 MAX R 1.65 .065 3.30 .130 Dimensions in mm inches 3 Red Yellow Green ABSOLUTE MAXIMUM RATINGS (T =25C) -9630 -9631 -9632 A Power Dissipation (mW) 100 60 100 Forward Current (mA) 30 20 30 Derating (mA/C) From 25C .4 .25 .4 Peak Current (mA) 120 80 120 Pulse width = 10s Operating Temperature (C) -55/+100 -55/+100 -55/+100 Storage Temperature (C) -55/+100 -55/+100 -55/+100 Soldering Temperature 260C, 5 seconds, 1.6 mm from case Red Yellow Green OPERATING CHARACTERISTICS (T =25C) -9630 -9631 -9632 A Luminous Intensity (mcd) Min. 3.7 3.7 2.5 I =10mA Typical 12.6 12.6 8.7 F Peak Wavelength (nm) Typical 635 585 565 Peak Viewing Angle ( ) Typical 38 38 38 21/2 Forward Voltage (V) Typical 2 2.1 2.1 I =20mA Max. 2.8 2.8 2.8 F Reverse Voltage (V), I =100A Min. 5 5 5 R 1 2is the off axis angle at which the luminous intensity is half the axial luminous intensity Dialight Corporation 1501 Route 34 South Farmingdale, NJ 07727 TEL: (732) 919-3119 FAX: (732) 751-5778 www.dialight.co m 3-13