812-0975 Dialight

INCANDESCENT PANEL MOUNT INDICATORS 004 & 113 SERIES FOR 15/32 MOUNTING HOLE LIGHT SHIELD 15/32 - 32 NS THD GASKET GASKET 4-40 Uses: 15/32 - 32 NS THD THD. BASE PART NO. VOLTAGE FIG T-1 3/4 MIDGET 004-1830-29-203 1.3528 1 Fig. 1 Fig. 2 FLANGE BASE INCANDESCENT 004-1930-29-203 1.3528 2 LAMP 23.81 WITH 20.24 WITH .94 LAMP .80 LAMP MAX MAX Fig. 3 Fig. 4 CAP PART NO. COLOR FIG CAP PART NO. COLOR FIG 3/8 - 24 UNF THD GASKET 004-2900-200 NO LENS 3 113-2931-203 RED 4 8.33 11.11 .33 .48 113-2937-203 CLEAR 4 6.35 .25 Material & Finish: Base - Black Nickel Plated Brass, PLASTIC FILTER 10.32 .41 15.08 Cap - Black Nickel Plated Brass with High Impact Plastic Lens .59 101, 111, 140 SERIES FOR 15/32 MOUNTING HOLE WATERTIGHT GASKET 15/32 - 32NS THD GASKET 15/32 - 32NS THD + CENTER CONTACT + CENTER CONTACT BASE PART NO. VOLTAGE FIG 1.19 .05 x Fig. 6 Fig. 5 1.19 .05 x 101-3830-09-203 1.3528 5 2.38 .09 2.38 .09 (2 SLOTS) (2 SLOTS) Uses: 101-8430-09-203 1.3528 6 17.46 T-1 3/4 MIDGET .69 21.43 MAX .84 MAX FLANGE BASE INCANDESCENT CAP PART NO. COLOR FIG CAP PART NO. COLOR FIG * * Fig. 7 Fig. 8 LAMP OR BASED 101-0937-003 CLEAR 7 111-0113-203 AMBER 8 GASKET LED LAMP** GASKET 5/16 - 32NS 101-0971-003 RED 7 111-0135-203 WHITE 8 THD 12.7 13.10 .50 .52 101-0972-003 GREEN 7 111-0137-203 CLEAR 8 6.75 101-0973-003 AMBER 7 140-1437-003 CLEAR 9 7.14 .27 .28 17.86 18.26 .70 Fig. 9 101-0975-003 WHITE 7 140-1471-003 RED 9 .72 MAX MAX GASKET 111-0111-203 RED 8 140-1472-003 GREEN 9 111-0112-203 GREEN 8 140-1473-003 AMBER 9 12.7 .50 140-1475-003 WHITE 9 6.75 .27 17.86 Material & Finish: Base - Black Nickel Plated Brass, Cap - High Impact Plastic .70 MAX Polycarbonate with Black Nickel Bezel (Fig. 8) ** Dialight recommends: Transparent lens caps for Based LEDs Clear lens caps for Green Based LEDs PART NUMBER ORDERING CODE PART NUMBER ORDERING CODE * * 101 09xx 003 111 01xx 203 Series 140 14xx 003 Lens Finish: 1 = Back Frosted Series Lens Finish: (Not available in white) 3 = Transparent** 3 = Transparent** 7 = Translucent (Not available in clear) 812 SERIES FOR 15/32 MOUNTING HOLE PRESS-TO-TEST Uses: Fig. 10 BASE PART NO. VOLTAGE FIG T-1 3/4 MIDGET FLANGE BASE 3/32 PRESS TO TEST FLANGE NUT 15/32 - 32NS THD INCANDESCENT LAMP OR BASED 812-1030-09-506 1.3528 10 2 LED LAMP** 1 CAP PART NO. COLOR FIG 3 * Fig. 11 22.23 812-0937 CLEAR 11 7.14 1.19 .05 x .88 .28 1.98 .08 MAX SLOTS 812-0971 RED 11 12.70 .50 812-0972 GREEN 11 812-0973 AMBER 11 5/16 - 32 18.26 NEF THD .72 MAX 812-0975 WHITE 11 PART NUMBER ORDERING CODE * 812 09xx Material & Finish: Base - Black Anodized Series Lens Finish: Aluminum, Cap - High Impact Plastic 3 = Transparent** 7 = Translucent ** Dialight recommends: Transparent lens caps for (Not available in clear) Based LEDs Clear lens caps for Green Based LEDs Neon and incandescent lamp information on Pages 35 and 36. Based LED lamp information on Pages on 37 through 40. Dialight Dimensions in mm inches 19 Dialight Corporation 1501 State Route 34 Farmingdale, NJ 07727 TEL: (732) 919-3119 FAX: (732) 751-5778 www.dialight.comX-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Switch Bezels / Switch Caps category: Click to view products by Dialight manufacturer: Other Similar products are found below : 896809000 LW1A-B2-R LW2A-B1-G 704.604.4 704.955.3 F1403 7527 760203000 760503000 766601000 785105000 785106000 79211759 MG12KB MH11 MH13 MHU31 MJ1216 MJ1226 MJ33 MJ612 MJ626 MJ627 9001T8BK 908-1634 92-343.200 92-343.400 95804.920 95CAP-011 95CAP-112 11-932.7 99-901.9 99-902.9 99-909.4 99-909.5 99-920.8 A0261A 11-931.2 11-932.5 11-936 11-937 AKTSC22B AW-RF8 161006 1825068-6 184-1872 187-1872 188-1471 1DFBLK 1D-GRY