1300 Henley Court Pullman, WA 99163 509.334.6306 www.digilentinc.com PmodAMP3 Reference Manual Revised April 15, 2016 This manual applies to the PmodAMP3 rev. A Overview The Digilent PmodAMP3 features an Analog Devices SSM2518 2 watt Class-D Audio Power Amplifier. The module enables the use of IS audio protocol or TDM to produce stereo audio at various sampling frequencies. Users may configure the digital volume and dynamic range control via an IC interface. Additionally, the PmodAMP3 may be used in a stand-alone mode that does not require the use of the IC interface. Features include: Audio amplifier with left and right channel separation Stereo output via two standard 1/8 (0.32 cm) mono speaker jacks Supports common IS audio formats Digitally configurable volume control for each channel Dynamic range control Stand-alone mode for systems without IC interface Small PCB size for flexible designs 1.5 0.8 (3.8 cm 2.0 cm) 12-pin Pmod port with IC interface The PmodAMP3. 1 Functional Description The PmodAMP3 utilizes Analog Devices SSM2518 to reproduce digitally fed audio signals in separate left and right headphone jacks. The separation of the jacks enables better audio signal isolation. 2 Interfacing with the Pmod The PmodAMP3 communicates with the host board via the IC protocol. Users may operate the PmodAMP3 in either an IC programmable mode or a simple stand-alone mode. The stand-alone mode is the default setting and can be activated by removing the shorting block on jumper JP5. When the stand-alone mode is active, jumpers JP3, JP4, and JP6 allow a simple hardware configuration of the amplifier. Within the stand-alone mode jumper JP3 configuration determines whether to use Standard or Left Justified IS protocol. Jumper JP4 determines if the MCLK input is 256 or 384 times the audio sampling frequency Fs. The jumper JP6 configures the amplifier to output at either 0dB or +12dB gain. Copyright Digilent, Inc. All rights reserved. DOC : 502-270 Page 1 of 3 Other product and company names mentioned may be trademarks of their respective owners. PmodAMP3 Reference Manual If JP5 is loaded, IC is enabled so that the on-board chip can be configured. Consequently, the shorting blocks on both JP3 and JP4 must be removed so that the SCL and SDA lines are pulled to a logic high voltage state. JP6 sets the IC address of the Pmod both addresses are valid, but a user may want to use one particular address if another IC device on the bus is using the other address. 2 JP5 Unloaded (default Stand-alone mode) JP5 Loaded (I C Programmable Mode) Loaded Unloaded Loaded Unloaded MCLK-provide own BCLK-route BCLK JP2 Don t Care Don t Care external MCLK to MCLK input 2 JP3 I S (Standard) Left Justified Prohibited Required JP4 256x Fs 384x Fs Prohibited Required JP6 12dB Gain 0dB Gain ADDR: 0110100 r/w ADDR: 0110110 r/w Table 1. Connector descriptions. Note: Both the 0dB and +12dB gain modes are very loud. You should take care to protect both yourself and your equipment when operating in stand-alone mode. Digilent recommends that you use the programmable mode and set the gain to -12dB or lower. The IC programmable mode is used to set alternate Master Clock (MCLK) and Bit Clock (BCLK) ratios as well as configure the Dynamic Range Control (DRC). More information about these options is available in our user guide. To transfer audio data in the IS audio format, the MCLK, BCLK, the Left/Right Word Clock (LRCLK), and the data (SDATA) will need to be provided either internally or externally as appropriate. This module is able to receive audio data anywhere between 8 and 32-bits of resolution. An example timing diagram from Texas Instruments on how IS data is to be sent to the module is provided below: 2 Figure 1. Example I S timing diagram. Copyright Digilent, Inc. All rights reserved. Page 2 of 3 Other product and company names mentioned may be trademarks of their respective owners.