Zynq 7000 SoC (Z7007S, Z7012S, Z7014S, Z7010, Z7015, and Z7020): DC and AC Switching Characteristics DS187 (v1.21) December 1, 2020 Product Specification Introduction The Zynq-7000 SoCs are available in -3, -2, -1, and -1LI devices are available in the commercial, extended, speed grades, with -3 having the highest performance. The industrial, or Q-temp temperature ranges. -1LI devices can operate at either of two programmable All supply voltage and junction temperature specifications logic (PL) V /V voltages, 0.95V and 1.0V, and are CCINT CCBRAM are representative of worst-case conditions. The parameters screened for lower maximum static power. The speed included are common to popular designs and typical specification of a -1LI device is the same as the -1 speed applications. grade. When operated at PL V /V = 0.95V, the CCINT CCBRAM -1LI static and dynamic power is reduced. Zynq-7000 device The available device/package combinations are outlined in: DC and AC characteristics are specified in commercial, Zynq-7000 SoC Overview (DS190) extended, industrial and expanded (Q-temp) temperature XA Zynq-7000 SoC Overview (DS188) ranges. Except for the operating temperature range or Defense-grade Zynq-7000Q SoC Overview (DS196) unless otherwise noted, all the DC and AC electrical parameters are the same for a particular speed grade (that This Zynq-7000 SoC data sheet, which covers the is, the timing characteristics of a -1 speed grade industrial specifications for the XC7Z007S, XC7Z012S, XC7Z014S, device are the same as for a -1 speed grade commercial XC7Z010, XA7Z010, XC7Z015, XC7Z020, XA7Z020, and device). However, only selected speed grades and/or XQ7Z020, complements the Zynq-7000 SoC documentation suite available on the Xilinx website at www.xilinx.com/zynq. DC Characteristics (1) Table 1: Absolute Maximum Ratings Symbol Description Min Max Units Processing System (PS) V PS internal logic supply voltage 0.5 1.1 V CCPINT V PS auxiliary supply voltage 0.5 2.0 V CCPAUX V PS PLL supply 0.5 2.0 V CCPLL V PS DDR I/O supply voltage 0.5 2.0 V CCO DDR (2) V PS MIO I/O supply voltage 0.5 3.6 V CCO MIO V PS input reference voltage 0.5 2.0 V PREF PS MIO I/O input voltage 0.40 V +0.55 V CCO MIO (2)(3)(4)(5) V PIN PS DDR I/O input voltage 0.55 V +0.55 V CCO DDR Programmable Logic (PL) V PL internal supply voltage 0.5 1.1 V CCINT V PL auxiliary supply voltage 0.5 2.0 V CCAUX V PL supply voltage for the block RAM memories 0.5 1.1 V CCBRAM V PL supply voltage for HR I/O banks 0.5 3.6 V CCO V Input reference voltage 0.5 2.0 V REF Copyright 20112020 Xilinx, Inc. Xilinx, the Xilinx logo, Zynq, Virtex, Artix, Kintex, Spartan, ISE, Vivado and other designated brands included herein are trademarks of Xilinx in the United States and other countries. AMBA, AMBA Designer, Arm, ARM1176JZ-S, CoreSight, Cortex, PrimeCell, Mali, and MPCore are trademarks of Arm Limited in the EU and other countries. All other trademarks are the property of their respective owners. DS187 (v1.21) December 1, 2020 www.xilinx.com Send Feedback Product Specification 1Zynq-7000 SoC (Z-7007S, Z-7012S, Z-7014S, Z-7010, Z-7015, and Z-7020) (1) Table 1: Absolute Maximum Ratings (Contd) Symbol Description Min Max Units I/O input voltage for HR I/O banks 0.40 V +0.55 V CCO (3)(4)(5) V IN I/O input voltage (when V =3.3V) for V and differential I/O standards CCO REF 0.40 2.625 V (6) except TMDS 33 V Key memory battery backup supply 0.5 2.0 V CCBATT GTP Transceiver (XC7Z012S and XC7Z015 Only) V Analog supply voltage for the GTP transmitter and receiver circuits 0.5 1.1 V MGTAVCC Analog supply voltage for the GTP transmitter and receiver termination V 0.5 1.32 V MGTAVTT circuits V Reference clock absolute input voltage 0.5 1.32 V MGTREFCLK V Receiver (RXP/RXN) and Transmitter (TXP/TXN) absolute input voltage 0.5 1.26 V IN I DC input current for receiver input pins DC coupled RX termination = floating 14 mA DCIN-FLOAT DC input current for receiver input pins DC coupled RX I 12 mA DCIN-MGTAVTT termination = V MGTAVTT I DC input current for receiver input pins DC coupled RX termination = GND 6.5 mA DCIN-GND I DC output current for transmitter pins DC coupled RX termination = floating 14 mA DCOUT-FLOAT DC output current for transmitter pins DC coupled RX I 12 mA DCOUT-MGTAVTT termination = V MGTAVTT XADC V XADC supply relative to GNDADC 0.5 2.0 V CCADC V XADC reference input relative to GNDADC 0.5 2.0 V REFP Temperature T Storage temperature (ambient) 65 150 C STG (7) Maximum soldering temperature for Pb/Sn component bodies +220 C T SOL (7) Maximum soldering temperature for Pb-free component bodies +260 C (7) T Maximum junction temperature +125 C j Notes: 1. Stresses beyond those listed under Absolute Maximum Ratings might cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those listed under Operating Conditions is not implied. Exposure to Absolute Maximum Ratings conditions for extended periods of time might affect device reliability. 2. Applies to both MIO supply banks V and V . CCO MIO0 CCO MIO1 3. The lower absolute voltage specification always applies. 4. For I/O operation, refer to the 7 Series FPGAs SelectIO Resources User Guide (UG471) or the Zynq-7000 SoC Technical Reference Manual (UG585). 5. The maximum limit applies to DC signals. For maximum undershoot and overshoot AC specifications, see Table 4. 6. See Table 11 for TMDS 33 specifications. 7. For soldering guidelines and thermal considerations, see the Zynq-7000 SoC Packaging and Pinout Specification (UG865). (1)(2) Table 2: Recommended Operating Conditions Symbol Description Min Typ Max Units PS V PS internal logic supply voltage 0.95 1.00 1.05 V CCPINT V PS auxiliary supply voltage 1.71 1.80 1.89 V CCPAUX V PS PLL supply 1.71 1.80 1.89 V CCPLL V PS DDR I/O supply voltage 1.14 1.89 V CCO DDR (3) V PS MIO I/O supply voltage for MIO banks 1.71 3.465 V CCO MIO DS187 (v1.21) December 1, 2020 www.xilinx.com Send Feedback Product Specification 2