PI3USB9281CGEEX Diodes Incorporated

PI3USB9281C USB 2.0 Port Protection with Charger Detection Description Features PI3USB9281C provides external detection for any USB- USB-device charger detector device. The part can detect various chargers available in Can tolerate USB3.0-PD with VBUS = 20V the market, MHL accessories, OTG accessories, and car- USB Charging-type detection chargers per the CEA936 spec. It also integrates a power Battery Charging 1.2 (BC1.2) DCP switch with over-voltage and over-current protections. Battery Charging 1.2 (BC1.2) CDP The VBUSIN input pin can tolerate voltages up to 28V, Battery Charging 1.2 (BC1.2) SDP which is important for USB3.0-PowerDelivery enabled Apple 1A, 2A & 2.4A dedicated chargers ports. The new USB-3.0-PowerDelivery specification Samsung-Fast chargers supports voltages up to 20V. YD/T-1951 dedicated chargers The PI3USB9281C can operate over a temperature range CEA-936 Carkit 1 and 2 chargers of -40 to +85C. Integrated Power FET Typical applications involve portable & consumer VBUS Tolerance up to 28V applications, such as tablet, smart phones, digital 1.7A Over-Current Protection (OCP) cameras, and notebooks with integrated Li-ion batteries VBUS Over-Voltage Protection (OVP) that charge via USB connectors. Non-charging Accessory Detection USB On-The-Go (OTG) detection Block Diagram Mobile HDMI Link (MHL) device detection Wide Supply Voltage Range 3V to 5.5V 2 I C Programmability Small Package: CSP 1.5x2.0-15L UQFN 3x4x0.5mm 20L Applications Personal Media Players Mobile Phones Tablet Figure 1. PI3USB9281C Block diagram All trademarks are property of their respective owners. www.diodes.com 9/30/2016 2016-09-0005 PT0574-1 1 PI3USB9281C Pin Configuration Top View GND VBUSDET NC VBUS VBUS VBUSOUT VBUS VBAT INTB C DET OUT IN SCL DPH B VDDIO SDA SCL ID D- SDA DNH GND INTB ENB DNH DPH D+ NC A VBAT NC 1 2 3 4 5 Figure 2a CSP 1.5x2.0-15L with 0.4mm Pitch Figure 2b UQFN 20L (3 X 4 X 0.5 mm) Pin Descriptions Name Type Default State Description USB Interface D+ signal switch path, dedicated USB port to be connected to the resident USB DPH Signal Path Open transceiver on the device D- signal switch path, dedicated USB port to be connected to the resident USB DNH Signal Path Open transceiver on the device Connector Interface ID Signal Path Open Connected to the USB connector ID pin and used for detecting accessories Connected to the USB connector D+ pin depending on the signaling D+ Signal Path Open mode D- Signal Path Open Connected to the USB connector D- pin depending on the signaling mode V Power Path NA Input voltage supply pin to be connected to the VBUS pin of the USB connector BUSIN Power Interface Input voltage supply pin to be connected to the device battery output or to an V Power NA BAT internal regulator V Power NA Baseband processor interface I/O supply pin DDIO ENB Input Hi-Z System enable for the circuit (Active Low) GND Power NA Ground Charger Interface V Power Path NA Output voltage supply pin to be connected to the source voltage pin on the charger IC BUSOUT Open-Drain V Hi-Z Open-drain active LOW output when VBUSIN is valid BUSDET Output 2 I C Interface 2 2 SCL Input Hi-Z I C serial clock signal to be connected to the phone-based I C master 2 2 SDA Open-Drain I/O Hi-Z I C serial data signal to be connected to the phone-based I C master 2 Interrupt active LOW output used to prompt the phone baseband processor to read the I C INTB CMOS Output LOW register bits, indicates a change in ID pin status or accessory attach status NC Hi-Z No Connection All trademarks are property of their respective owners. www.diodes.com 9/30/2016 2016-09-0005 PT0574-1 2 ID NC D+ VDDIO ENB D- NC VBUSIN