A product Line of Diodes Incorporated PI5C3309 3:1 Mux/DeMux Bus Switch Features Description Near-Zero propagation delay Diodes PI5C3309 is a 3:1 Multiplexer/Demultiplexerwith 3-State outputs. Inputs can be connected to outputs with lowOn- 5-ohm switches connect inputs to outputs Resistance (5-ohm) with no additional ground bounce noise Direct bus connection when switches are ON orpropagation delay. Ultra Low Quiescent Power (0.2A typical) Ideally suited for notebook applications Packaging (Pb-free & Green available): 8 pin 118-mil wide plastic MSOP (U) Block Diagram Pin Configuration IA IA IA 0 1 2 IA 1 8 V 0 CC S 0 IA 2 7 S 1 1 S 1 IA 3 6 S 2 0 GND 4 5 YA YA (1) Truth Table Pin Description Pin Name Description Select IAn Data Inputs S1 S0 YA Function S0-1 Select Inputs L L IA0 S1-0 = 0 YA Data Output L H IA1 S1-0 = 1 GND Ground H L IA2 S1-0 = 2 V Power CC H H Hi-Z S1-0 = 3 Note: 1. H = High Voltage Level L = Low Voltage Level www.diodes.com March 2018 PI5C3309 1 Diodes Incorporated Document Number DS40822 Rev 1-2 A product Line of Diodes Incorporated PI5C3309 Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Note: Storage Temperature ......................................................... 65C to +150C Stresses greater than those listed under MAXIMUM Ambient Temperature with Power Applied ........................ 40C to +85C RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation Supply Voltage to Ground Potential (Inputs & V only) .. 0.5V to +7.0V CC of the device at these or any other conditions above Supply Voltage to Ground Potential (Outputs & D/O only) 0.5V to +7.0V those indicated in the operational sections of this specification is not implied. Exposure to absolute DC Input Voltage ................................................................. 0.5V to +7.0V maximum rating conditions for extended periods may DC Output Current ............................................................................ 120mA affect reliability. Power Dissipation .................................................................................0.5W DC Electrical Characteristics (Over Operating Range, T = 40C to +85C, V = 5V 5%) A CC (1) (2) Parameters Description Test Conditions Min. Typ. Max. Units V Input HIGH Voltage Guaranteed logic HIGH level 2.0 IH V V Input LOW Voltage Guaranteed logic LOW level 0.5 0.8 IL I Input HIGH Current V = Max., V = V 1 IH CC IN CC I Input LOW Current V = Max., V = GND 1 A IL CC IN I High Impedance Output Current 0 I , Y V 1 OZH N N CC V Clamp Diode Voltage V = Min, I = -18mA 0.7 1.2 V IK CC IN I Short Circuit current I(Y)=0V, Y(I)=V 100 mA OS CC V Input Hysteresis at Control Pins 150 mV H V = Min., V = 0.0V, I = 48mA 5 7 CC IN ON (4) R Switch on Resistance ON V = Min., V = 2.4V, I = 15mA 10 15 CC IN ON Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at V = 5.0V, T = 25C ambient and maximum loading. CC A 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. Measured by the voltage drop between I and Y pin at indicated current through the switch. On-Resistance is determined by the lower of the voltages on the two (I, Y) pins. Capacitance (T = 25C, f = 1 MHz) A (1) Parameters Description Test Conditions Typ. Units C Input Capacitance 3 IN C I Capacitance, Switch Off V = 0V 4 pF OFF A IN C I Capacitance, Switch On 16 ON A Notes: 1. This parameter is determined by device characterization but is not production tested. www.diodes.com March 2018 PI5C3309 2 Diodes Incorporated Document Number DS40822 Rev 1-2