ZABG6004 6 STAGE FET LNA BIAS CONTROLLER Summary The ZABG6004 is an advanced GaAs and HEMT FETs bias controller designed to operate from minimal supply rails and intended primarily for satellite Low Noise Blocks (LNBs). With the addition of one capacitor and two resistors, the ZABG6004 provides drain voltage and current control for up to 6 external grounded source FETs. Generating the regulated negative rail required for FET gate biasing whilst operating from a single supply of 2.1V to 5V. The -2V negative bias can also be used to supply other external circuits. Setting drain currents on the ZABG6004 uses two resistors and drain current control is split between the six FETs in a group of two and a group of four. This allows the operating current of input FETs to be adjusted to minimize noise, whilst the following FET stages can be adjusted for maximum gain. Features Applications Provides Bias for up to 6 GaAs and HEMT FETs Low Power LNBs Operating Range of 2.1V to 5V Digital LNBs Ultra-low Operating Current of 1.1mA IP LNBs Dynamic FET Protection Twin LNBs and Quad LNBs Amplifier FET Drain Current Selectable (4mA to 15mA) General Purpose LNA Bias Regulated Negative Rail Generator Requires only 1 External Capacitor Expended Temperature Range of -40C to +105C U-QFN3030-16 (Type B) and QSOP-20 Surface Mount Package Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2) Halogen and Antimony Free. Green Device (Note 3) Notes: 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant. 2. See ZABG6004 Device Description The ZABG series of devices are designed to meet the bias requirements of GaAs and HEMT FETs commonly used in satellite receiver LNBs with a minimum of external components whilst operating from a minimal voltage supply and using minimal current. The ZABG6004 has six FET bias stages that can be programmed to provide a constant drain current. Programming of the FET bias stage arrangement and the operating currents of each FET group is achieved by resistors connected to the R and R pins, allowing input FETs CAL1 CAL2 to be biased for optimum noise and the later stages for optimum gain. All FET groups can be operated at currents in the range 4mA to 15mA, R sets the drain current for D1 and D4 and R sets the drain current for D2, D3, D5 and D6. It is not recommended to connect R and CAL1 CAL2 CAL1 R together. CAL2 Drain voltages of amplifier stages are set at 2.0V and are current limited to approximately current set by their associated R resistors. CAL Depletion mode FETs require a negative voltage bias supply when operated in grounded source circuits. The ZABG6004 includes an integrated switched capacitor DC-DC converter generating a regulated output of -2V to allow single supply operation. The ZABG6004 has been designed to be used with supply rails of 2.1V to 5.0V and the V range has been extended to 5.5V to allow for 10% supply variation. DD It is possible to use less than the full complement of FET bias controls, unused drain and gate connections can be left open circuit without affecting operation of the remaining bias circuits. To protect the external FETs the circuits have been designed to ensure that, under any conditions including power up/down transients, the gate drive from the bias circuits cannot exceed -2.5V. Additionally each stage has its own individual current limiter. Furthermore if the negative rail experiences a fault condition, such as overload or short circuit, the drain supply to the FETs will be limited, avoiding excessive current flow. The ZABG6004 is available in the U-QFN3030-16 (Type B) and the QSOP-20 packages. Device operating temperature is -40C to +105C to suit a wide range of environmental conditions. 2 of 11 ZABG6004 March 2017 Diodes Incorporated www.diodes.com Document number: DS38917 Rev. 2 - 2 NEW PRODUCT