ZLDO1117K15TC Diodes Incorporated

A Product Line of Diodes Incorporated ZLDO1117 1A LOW DROPOUT POSITIVE REGULATOR 1.2V, 1.5V, 1.8V, 2.5V, 3.3V, 5.0V AND ADJUSTABLE OUTPUTS Description Pin Assignments ZLDO1117 is a low dropout positive adjustable or fixed-mode SOT223 regulator with 1A output current capability. The ZLDO1117 has a 2% tolerance across the industrial temperature range and is guaranteed to have lower than 1.2V dropout at full load current making it ideal to provide well-regulated outputs of 1.2V to 5.0V with input supply voltages up to 18V. The ZLDO1117 is ideally suited to provide well-regulated supplies for low voltage IC applications such as high-speed bus termination and low current 3.3V logic supply across the whole industrial temperature range. TO252 (Top View) Features Vin 3 1.2V Maximum Dropout at Full Load Current 2 Vout 2% Tolerance Over Temperature, Line and Load Variations 1 Adj (GND) Fast Transient Response Tab is Vout Output Current Limiting Built-in Thermal Shutdown Good Noise Rejection Suitable for use with MLCC Capacitors Qualified to AEC-Q100 Grade 2 (see Ordering Information) PPAP capable (Note 4) -40 to +125C Junction Temperature Range Available in TO252 and SOT223 with Green Molding Compound (No Br, Sb) Lead-Free Finish RoHS Compliant (Notes 1 & 2) Halogen and Antimony Free. Green Device (Note 3) Notes: 1. EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant. All applicable RoHS exemptions applied. 2. See A Product Line of Diodes Incorporated ZLDO1117 Pin Descriptions Pin Pin I/O Function Number Name A resistor divider from this pin to the V pin and ground sets the output voltage (Ground only for OUT Adj (GND) I 1 Fixed-Mode). The output of the regulator. A minimum of 4.7F capacitor (0.05 ESR 0.5 ) must be connected V O 2 OUT from this pin to ground to insure stability. For improved ac load response a larger output capacitor is recommended. The input pin of regulator. Typically a large storage capacitor (0.05 ESR 0.5 ) is connected from this pin to ground to ensure that the input voltage does not sag below the minimum dropout voltage V I 3 IN during the load transient response. This pin must always be 1.3V higher than V in order for the OUT device to regulate properly. Absolute Maximum Ratings ( T = +25C, unless otherwise specified.) A Symbol Parameter Rating Unit V Input Supply Voltage (Relative to Ground) -0.03 to +18 V IN T Junction Temperature +150 C J Power Dissipation See SOA Curve T Storage Temperature -65 to +150 C ST Unless otherwise stated voltages specified are relative to the ANODE pin. 1.2 1 0.8 0.6 SOA 0.4 0.2 0 0 5 10 15 20 25 V - V (V) IN OUT Safe Operation Area (SOA) Curve ESD Susceptibility Symbol Parameter Rating Unit HBM Human Body Model 4 kV MM Machine Model 400 V Stresses greater than the Absolute Maximum Ratings specified above, may cause permanent damage to the device. These are stress ratings only functional operation of the device at these or any other conditions exceeding those indicated in this specification is not implied. Device reliability may be affected by exposure to absolute maximum rating conditions for extended periods of time. Semiconductor devices are ESD sensitive and may be damaged by exposure to ESD events. Suitable ESD precautions should be taken when handling and transporting these devices 2 of 14 July 2012 ZLDO1117 Diodes Incorporated www.diodes.com Document number: DS32018 Rev. 6 - 2 I (A) LOAD