3.2008 LCD-MODULE 2x16 - 6.68mm INCL. CONTROLLER HD44780 EA DIP162J-DN3LW 75 x 27 x 11 mm EA DIP162-DN3LW 75 x 27 x 11 mm EA DIP162-DHNLED 68 x 27 x 11 mm FEATURES * HIGH CONTRAST LCD SUPERTWIST DISPLAY * EA DIP162-DNLED: YELLOW/GREEN WITH LED BACKLIGHT * EA DIP162-DN3LW AND DIP162J-DN3LW WITH WHITE LED B/L., LOW POWER * INCL. HD 44780 OR COMPATIBLE CONTROLLER * INTERFACE FOR 4- AND 8-BIT DATA BUS * POWER SUPPLY +5V OR 2.7V OR 3.3V * OPERATING TEMPERATURE 0~+50C (-DN3LW, -DHNLED: -20~+70C) * LED BACKLIGHT Y/G max. 150mA +25C * LED BACKLIGHT WHITE max. 45mA +25C * SOME MORE MODULES WITH SAME MECHANIC AND SAME PINOUT: -DOTMATRIX 1x8, 4x20 -GRAPHIC 122x32 * NO SCREWS REQUIRED: SOLDER ON IN PCB ONLY * DETACHABLE VIA 9-PIN SOCKET EA B200-9 (2 PCS. REQUIRED) ORDERING INFORMATION LCD MODULE 2x16 - 6.68mm WITH BACKLIGHT Y/G EA DIP162-DNLED SAME BUT WITH T -20..+70C INCL. TEMP. COMPENSATION EA DIP162-DHNLED OP. SAME IN BLUE-WHITE OPTIC, T -20..+70C INCL. TEMP. COMP. EA DIP162-DN3LW OP. SAME IN BLACK&WHITE, T -20..+70C INCL. TEMP. COMP. EA DIP162J-DN3LW OP. 9-PIN SOCKET, HEIGHT 4.3mm (1 PC.) EA B200-9 SUITABLE BEZEL (WINDOW 60.0x14.8 mm) EA 017-2UKE ADAPTOR PCB WITH STANDARD PINOUT PITCH 2.54mm EA 9907-DIP Zeppelinstrae 19 D-82205 Gilching Phone +49-(0)8105-778090 Fax +49-(0)8105-778099 www.lcd-module.de info lcd-module.de no mounting requiredSpecifications may be changed without EA DIP162-D prior notice. Printing error reserved Page 2 5V operation Pinout Pin Symbol Level Function Pin Symbol Level Function 1 VSS L Power Supply 0V (GND) 10 D3 H/L Display Data 2 VDD H Power Supply +5V 11 D4 (D0) H/L Display Data 3 VEE - Contrast adjust. (about 0V) 12 D5 (D1) H/L Display Data 4 RS H/L H=Command, L=Data 13 D6 (D2) H/L Display Data 5 R/W H/L H=Read, L=Write 14 D7 (D3) H/L Display Data, MSB 3.3V operation 6 E H Enable (falling edge) 15 - - NC (see EA DIP122-5N) 7 D0 H/L Display Data, LSB 16 - - NC (see EA DIP122-5N) 8 D1 H/L Display Data 17 A - LED B/L+ Resistor required 9 D2 H/L Display Data 18 C - LED B/L - Contrast Adjustment Contrast voltage for all displays of EA DIP162-D series is typ. 5V. That means that for 3.3V operation an additional negative voltage of min. 1.7V is required. Display modules for -20..+70C are equipped with an on-board temperature compensation. So there s no more need for contrast adjustment while operation anymore. Backlight Using the LED backlight requires an current source or external current-limiting resistor. Forward voltage for yellow/green backlight is 3.9~4.2V and for white LED backlight 3.0~3.6V. Please take care of derating for T >+25C a Note: Do never drive backlight direct to 5V immediately damage my happen Character set Character set shown below is already built in. In addition to that you are able to define up to 8 characters by yoursself.