EA DIP203J-6NLW Display Visions

Issue 4.2013 LCD-Modul 4x20 - 6.45mm INCL. CONTROLLER SSD1803 EA DIP203B-6NLW EA DIP203J-6NLW: Dimension 75 x 46 mm FEATURES * HIGH-CONTRAST LCD-SUPERTWIST DISPLAY * BLUE BACKGROUD WITH WHITE CHARACTERS * BLACK&WHITE FSTN * EXTREME COMPACT WITH 75mm WIDTH * BUILT-IN CONTROLLER SSD1803 (VERY SIMILAR TO HD44780) * 4- AND 8-BIT INTERFACE FOR DATABUS * SERIAL SPI-INTERFACE (SID, SOD, SCLK, CS) * POWER SUPPLY +3.3V / TYP. 4mA (w./o. B./L.) * OPERATING TEMP. RANGE -20..+70C * AUTOMATIC TEMPERATURE COMPENSATION BUILT-IN * LED-BACKLIGHT WHITE, max. 75mA +25C * 16 ICONS (BATTERY, ARROWS ETC.) AT THE TOP EDGE * NO MONTING IS REQUIRED: JUST SOLDER INTO PCB * SINGLE ROW SOCKET AVAILABLE: EA B254-12 (1 PC.) * 128x64 GRAPHIC WITH SAME DIMENSION AND SAME PINOUT: EA DIP128 ORDERING INFORMATION LCD-MODULE 4x20 - 6.45mm WITH LED-B./L. BLUE EA DIP203B-6NLW FSTN BLACK ON WHITE EA DIP203J-6NLW SOCKET 4.5mm HEIGHT, 12 POSITIONS (1 PC.) EA B254-12 no mounting requiredEA DIP203-6 PINOUT 4-/8-Bit Mode (Factory Set) SPI Mode (Solder linkSP closed) Pin Symbol Function Pin Symbol Function Pin Symbol Function Pin Symbol Funktion 1 VSS Power Supply 0V (GND) 13 not connected 1 VSS Power Supply 0V (GND) 13 not connected 2 VDD Power Supply +3.3 V 14 VSS Power Supply 0V (GND) 2 VDD Power Supply +3.3V 14 VSS Power Supply 0V (GND) 3 VCI Contrast Adjustment 15 D0 Display Data, LSB 3 VCI Contrast Adjustment 15 SOD Data Out 4 RES L: Reset 16 not connected 4 RES L: Reset 16 D1 Display Data D1 5 RS H=Data L=Command 17 D2 Display Data D2 5 CS Chip Select 17 not connected 6 R/W H=Read, L=Write 18 D3 Display Data D3 6 SID Data In 18 not connected 7 SCLK Shift Clock 19 not connected 7 E Enable 19 D4 (D0) Display Data D4 8 not connected 20 D5 (D1) Display Data D5 8 not connected 20 not connected 9 not connected 21 D6 (D2) Display Data D6 9 not connected 21 not connected 10 not connected 22 not connected 10 not connected 22 D7 (D3) Display Data, MSB 11 not connected 23 A LED-B/L + (ext. Resistor requ) 11 not connected 23 A LED-B/L + (ext. Resistor requ) 12 not connected 24 C LED-B/L - 12 not connected 24 C LED-B/L - BACKLIGHT Using the LED backlight requires a current source or external current-limiting resistor. Forward voltage for white LED backlight is 3.0~3.6V. Please take care of derating for T >+25C a Attention: Do never drive backlight directly to VDD this may damage backlight immediately The blue display cannot be read without backlight. For direct sunlight we suggest to use the J-type. TABLE OF COMMAND (SSD1803) Code Execute Instruction Description Time RE DB DB DB DB DB DB DB DB R/W RS Bit 7 6 5 4 3 2 1 0 (270kHz) Clears all display and returns the cursor to the Clear Display * 0 0 0 00 0 0 00 1 1.53ms home position (Address 0). Returns the Cursor to the home position (Address 0). Also returns the display being shifted to the Cursor At Home 0 0 0 0 0 0 0 0 0 1 * 1.53ms original position. DD RAM contents remain unchanged. Set Pow er dow n mode bit. Power Down 1 0 0 0 0 0 0 0 0 1 PD PD=0: pow erdow n mode disable 39s Mode PD=1: pow erdow n mode enable Cursor moving direction (I/D=0: dec I/D=1: inc) 0 0 0 0 0 0 0 0 1 I/D S 39s shift enable bit (S=0: disable S=1: enable shift) Entry Mode Set Segment bidirectional function 0 0 0 0 0 0 0 0 1 1 BID 39s (BID=0: Seg1->Seg60 BID=1: Seg60->Seg1) D=0: display off D=1: display on Display On/Off C=0: cursor off C=1: cursor on 0 0 0 0 00 0 1 DC B 39s Control B=0: blink off B=1: blink on FW=0: 5-dot font w idth FW=1: 6-dot font w idth extended BW=0: normal cursor BW=1: inverting cursor 1 0 0 0 00 0 1 FW BW NW 39s Function Set NW=0: 1- or 2-line (see N) NW=1: 4-line display Moves the Cursor or shifts the display Cursor / Display S/C R/L S/C=0: cursor Shift S/C=1: display shift 0 0 0 0 00 1 * * 39s Shift R/L=0: shift to left R/L=1: shift to right Determine the line for horizontal scroll Scroll Enable 1 0 0 0 0 0 1 H4 H3 H2 H1 39s sets interface data length (DL=0:4-bit DL=1:8-bit) number of display lines (N=0: 1-line N=1: 2-line) REV 0 0 0 0 0 1 DL N RE DH extension register (RE= 0/1) 39s scroll/shift (DH=0: dot scroll DH=1: display shift) Function Set reverse bit (REV=0:normal REV=1:inverse display) CG-/SEG-RAM blink (BE=0: disable BE=1: 1 0 0 0 0 1 DL N RE BE LP enable) 39s LP=0: normal mode LP=1: low pow er mode CG RAM Sets the CG RAM address. CG RAM data is sent 0 0 0 0 1 AC 39s and received after this setting. Address Set SEG RAM Sets the SEG RAM address. SEG RAM data is 1 0 0 0 1 * * AC 39s sent and received after this setting. Address Set DD RAM Sets the DD RAM address. DD RAM data is sent 0 0 0 1 AC 39s and received after this setting. Address Set Set Scroll SQ Sets the quantity of horizontal dot scroll (DH=0) 1 0 0 1 * 39s Quantity Reads Busy flag (BF) indicating internal operation Busy Flag / is being performed and reads address counter * 0 1 BF AC - Address Read contents. Writes data into internal RAM Write Data * 1 0 Write Data 43s (DD RAM / CG RAM / SEGRAM) Reads data from internal RAM Read Data * 1 1 Read Data 43s (DD RAM / CG RAM / SEGRAM) SERIAL MODE SPI Factory set for interface is parallel with 4 bit or 8 bit data bus. Alternative module can be programmes with serial data stream. For that solder link SPI has to be closed. Harware specification for serial operation mode is written down in user manual for SSD1803: