EA DIP128-6N5LWTP Issue 8.2013 EA DIP128-6 8.2008 LCD-GRAFIC MODULE 128x64 DOTS EA DIP128J-6N5LW EA DIP128J-6N5LE EA DIP128J-6N5LA FEATURES 75,0 x 45,8 x 10,8 mm * REAL BRIGHT AND CONTRASTY GRAPHIC DISPLAYS * EA DIP128-6N5LW: WHITE DOTS, BLUE BACKGROUND * EA DIP128J-6N5LW: BLACK DOTS, WHITE BACKGROUND * WITH AMBER BACKLIGHT (LONGLIFE) * GREEN VERSION FOR HIGHEST CONTRAST * LOW-POWER LED BACKLIGHT min. 15mA, max. 90mA +25C * INTEGRATED CONTROLLER KS0107/108 OR PT6607/08 * TEMPERATURE COMPENSATION BUILT-IN * 8-BIT BUS INTERFACE * NO MOUNTING REQUIRED: JUST SOLDER INTO PCB * POWER SUPPLY +5V * OPERATING TEMPERATURE RANGE -20C..+70C ACCESSORIES * MATRIX TOUCH PANEL 5x3, ANTIGLARE AND SCRATCH-PROOF * HIGH-LEVEL-GRAPHICS-CONTROLLER FOR RS-232: EA IC202-PGH ORDERING INFORMATION LCD GRAPHIC MODULE 128x64 DOTS BLUE-WHITE EA DIP128-6N5LW SAME BUT IN BLACK/WHITE OPTIC EA DIP128J-6N5LW WITH AMBER BACKLIGHT EA DIP128J-6N5LA WITH GREEN BACKLIGHT EA DIP128J-6N5LE ALL WITH TOUCH PANEL, 5x3 FIELDS EA DIP128x-xxxxxTP SOCKET 4.5mm HEIGHT, 12 PINS (1 pc.) EA B254-12 ZIFF CONNECTOR (SMD) FOR TOUCH PANEL EA WF100-10S Zeppelinstr. 19 D-82205 Gilching Tel. 08105-778090 Fax 08105-778099 www.lcd-module.de info lcd-module.de with pinsELECTRONIC ASSEMBLY reserves the right to change specifications EA DIP128-6 without prior notice. Printing and typographical errors reserved. Page 2 PINOUT Pin Symbol Function Pin Symbol Function 1 VSS Power Supply 0V (GND) 13 VNEG neg. voltage output f. contrast 2 VDD Power Supply +5V 14 NC not connected 3 ADJ Contrast adjustment 15 D0 Display Data, LSB 4 RES L: Reset 16 D1 Display Data 5 D/I H=Data L=Command 17 D2 Display Data 6 R/W H=Read, L=Write 18 D3 Display Data 7 E1 Enable left half of display 19 D4 Display Data 8 E2 Enable right half of display 20 D5 Display Data 9 CS1L L: Chipselect left, low active 21 D6 Display Data 10 CS1H H: Chipselect left, high active 22 D7 Display Data, MSB 11 CS2L L: Chipselect right, low active 23 A LED + (ext. series resistor ) 12 CS2H H: Chipselect right, high active 24 C LED - CONTRAST is already adjusted for 5V when shipped out. Once contrast is set to an optimum, internal temperature compensation circuit provides best contrast allover the whole temperature range of -20..+70C. An external contrast adjustment is normally not necessary, but can be done via external potentiometer. BACKLIGHT Graphic displays EA DIP128-6 are featured with a low-power LED-backlight. Brightness can be switched off and adjusted infinitely. Driving the LED backlight requires a current source or an external series resistor for current limiting. Forward voltage is between 2.2..2.6V (amber), 3.9..3.6V (white), 3.7..4.1V (green). Maximum supply current is 90mA +25C. Operating with 5V we Amber Backlight recommend a limiting resitor for amber of 12 Ohm, for the white one of 24 Ohm and for the green one of 15 Ohm. Please take care of derating when used at t >+25C. a Attention: Do never drive backlight direct to 5V this may cause immediately defect Note: Blue-white version provide no contrast when backlight is switched off. Reading the display requires a minimum of backlight with about 15mA. BLACK&WHITE, BLUE, AMBER, GREEN The blue-white display EA DIP128-6N5LW is best for indoor use with and without ambient light. Reading the display requires a minimum of backlight with about 15mA. Black and white version EA DIP128J-6N5LW and green version are especially designed for outdoor applications. These displays do provide best contrast for all ambient illuminations, even with direct sunlight. No need to say that display can be read in darkness when LED backlight is switched on. This is same for the amber backlighted version EA DIP128J-6N5LA. The greatest advantage here is the long life backlight. APPLICATION EXAMPLES Besides you can see some application examples. Example 3: 2x Enable, no CS Example 1: Enable and CS lo- Example 4: Enable and left/right Example 2: Enable and CS hi-