LIMITATION OF LIABILITY DANIELS MANUFACTURING CORPORATION IS NOT LIABLE FOR CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY NATURE OR KIND RE SUL TING FROM THE USE, OR MISUSE, OF ANY OF ITS PRODUCTS. OWNERS AND USERS OF DMC PRODUCTS ASSUME FULL RESPONSIBILITY FOR INSTRUCTING THEIR EMPLOYEES IN THE PROPER AND SAFE USE OF SUCH PRODUCTS. LIMITED WARRANTY DMC (Daniels Manufacturing Corporation) warrants each new product sold by it to be free from defects in material and workmanship under normal use and service. DMC s obligation under this warranty is limited to the free correction or, at DMC s option, the refund of the purchase price of any such product which proves defective in normal service within ninety (90) days ofter delivery to the first user, provided that the product is returned to DMC with all transportation charges prepaid and which shall appear to DMC s satisfaction, after DMC s inspection, to hove been defective in material or workmanship, it being understood that DMC products are not consumer products. This warranty shall not cover any damage to any product which, in the opinion of DMC, was caused by normal wear, misuse, improper operation, tampering, neglect or occident. This warranty is in lieu of all other warranties express or implied. No warranty, express or implied, is mode or authorized to be mode or assumed with respect to products of Daniels Manufacturing Corporation other than those herein set forth. UH2-5 Dl .,.DANltLS MANUFACTURING - ---CORPORA noN UNIVERSAL POSmONER DATASHEET SEE REVERSE SIDE FOR IMPORTANT INFORMATION CONCERNING LIMITED WARRANTY, AND LIMITATION OF LIABILITY. OUT UH2-5 (M22520/1-05) Universal Head Assembly is used with AFB (M22520/1-01) Crimping Tool to locate contacts horizontally and vertically between indenters. INSTRUCTIONS 1. With Universal Positioner over crimp tool, align socket head mounting screws with topped holes in tool. Tighten mounting screws. 2. Raise and rotate selector knob until desired wire size, indicated on selector knob, is in line with SEL. NO. index on tool body 3. Note that selector settings shown on selector knob are based on combinations of MIL-W-16878 silver plated stranded wire ond MS.3190 contact wire barrels. User must establish appropriate selector settings for other contact wire combinations. 4. With lock nut in release position, turn adjustment screw IN until it stops. Insert contact through indenter opening into positioner and adjust screw OUT until indenters ore centered between inspection hole and barrel end of contact. When contact contains insulation cup, center between inspection hole and bottom of insulation cup. 5. Tighten lock nut to body. Tool is now ready for crimping operation. / / DANIELS MANUFACTURING CORP., 526 THORPE ROAD, ORLANDO, FL 32824, USA, PHONE 407 855-6161, FAX 407 855-6884 COPYRIGHT 01996 DANIELS MANUFACTURING CORP., USA. WWW.DMCTOOLS.CO>.A E-MAIL: OMCCOMCTOOLS.COM ALL RIGHTS RESERVED. 3/96 REV. A UH2-5-0S UH2-5 DIC ,aADANIELS MANUFACTURING ., ... CORPORAnON DATASHEET UNIVERSAL POSmONER SEE REVERSE SIDE FOR IMPORTANT INFORMATION CONCERNING LIMITED WARRANTY, AND LIMITATION OF LIABILITY. OUT UH2-5 (M22520/1-05) Universal Head Assembly is used with AFB (M22520/1-01) Crimping Tool to locate contacts horizontally and vertically between indenters. INSTRUCTIONS LOCKNUT IN RELEASE POSITION 1. With Universal Positioner over crimp tool, align socket head mounting screws with topped holes in tool. Tighten mounting screws. 2. Raise and rotate selector knob until desired wire size, indicated on selector knob, is in line with SEL. NO. index on tool body 3. Note that selector settings shown on selector knob are based on combinations of MIL-W-16878 silver plated stranded wire and MS.3190 contact wire barrels. User must establish appropriate selector settings for other con tact wire combinations. 4. With lock nut in release position, turn adjustment screw IN until it stops. Insert contact through indenter opening into positianer and adjust screw OUT until indenters ore centered between inspection hole ond barrel end of contact. When contact contains insulation cup, center between inspection hole and bottom of insulation cup. 5. Tighten lock nut to body. Tool is now ready for crimping operation. SELECTOR KNOB DANIELS MANUFACTURING CORP., 526 THORPE ROAD, ORLANDO, FL .32824, USA, PHONE 407/855-6161, FAX 407/855-6884 COPYRIGHT C) 1996 DANIELS MANUFACTURING CORP., USA. WWW.DMCTOOLS.COM E-MAIL: DMCGOMCTOOLS.COM ALL RIGHTS RESERVED 3/96 REV. A UH2-5-0S LIMITATION OF LIABILITY DANIELS MANUFACTURING CORPORATION IS NOT LIABLE FOR CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY NATURE OR KIND RESULTING FROM THE USE, OR MISUSE, OF ANY OF ITS PRODUCTS. OWNERS AND USERS OF DMC PRODUCTS ASSUME FULL RESPONSIBILITY FOR INSTRUCTING THEIR EMPLOYEES IN THE PROPER AND SAFE USE OF SUCH PRODUCTS. LIMITED WARRANTY DMC (Daniels Manufacturing Corporation) warrants each new product sold by it to be free from defects in material and workmanship under normal use and service. DMC s obligation under this warranty is limited to the free correction or, at DMC s option, the refund of the purchase price of any such product which proves defective in normal service within ninety (90) days ofter delivery to the first user, provided that the product is returned to DMC with all transportation charges prepaid and which shall appear to DMC s satisfaction, ofter DMC s inspection, to hove been defective in material or workmanship, it being understood that DMC products ore not consumer products. This warranty shall not cover any damage to any product which, in the opinion of DMC, was caused by normal wear, misuse, improper operation, tampering, neglect or occident. This warranty is in lieu of all other warranties express or implied. No warranty, express or implied, is mode or authorized to be mode or assumed with respect to products of Daniels Manufacturing Corporation other than those herein set forth.