Nuts Brass aand SSteel Hexagonal Thin (or Lock) Nut Hexagonal Ordinary Nut Hexagonal Ordinary Nut Dimensions : Millimetres (Inches) Specifications Alternative chamfering permissible on sizes 13 B.A. and smaller. Width Thickness Width Across Flats Across Nominal Diameter (A) Corners Ordinary (or Full) Nuts Thin (or Lock) Nuts B.A. No. of Thread (E) (B) (C) (D) Maximum Minimum Maximum Maximum Minimum Maximum Minimum 8 2.2 (0.087) 3.9 (0.152) 3.8 (0.149) 4.6 (0.18) 2.1 (0.082) 1.9 (0.075) 1.5 (0.058) 1.3 (0.051) 6 2.8 (0.110) 4.9 (0.193) 4.8 (0.189) 5.6 (0.22) 2.7 (0.105) 2.4 (0.095) 1.9 (0.073) 1.6 (0.063) 4 3.6 (0.142) 6.3 (0.248) 6.2 (0.243) 7.4 (0.29) 3.4 (0.135) 3.2 (0.125) 2.4 (0.094) 2.1 (0.084) 2 4.7 (0.185) 8.2 (0.324) 8.1 (0.319) 9.4 (0.37) 4.2 (0.167) 4.0 (0.157) 3.1 (0.123) 2.9 (0.113) Dimensions : Millimetres (Inches) Specification Table Description B.A. No. Part Number Nut, Brass, NP, BX100 8 NX51080007FA Nut, Brass, NP, BX100 6 NX51060007FA Nut, Brass, NP, BX100 4 NX51040007FA Nut, Brass, NP, BX100 2 NX51020007FA Nut, Steel, Zinc Plated, BX100 6 NC51060081FA Nut, Steel, Zinc Plated, BX100 4 NC51040081FA Disclaimer This data sheet and its contents (theInformatio) belong to the Premier Farnell Group (theGrou) or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group s liability for death or personal injury resulting from its negligence. DURATOOL is the registered trademark of the Group. Premier Farnell plc 2009. X-ON Electronics Authorized Distributor Click to view similar products for Duratool manufacturer. Other Similar products are found below : 0110763 0110764 0110765 0110767 0110768 0110769 0110770 0110771 0210006 0210009 0290901 08BL0BK3AS3K 08BS0BK3AS3K 08BSOHK3AS3K 08KMFTO3AS1E 08OMFHK3AS1E 101ATN 101BTN 101CTN 101FTN 101VTN 1024N 1026N 102VN 10AW06