REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED 94-10-24 M. A. Frye A Added 3 devices, 02 - 04. Updated format, editorial change throughout. 97-02-26 Ray Monnin B Add 05 device, update format, editorial changes throughout. 07-03-23 Robert M. Heber C Boilerplate update, part of 5 year review. ksr REV SHEET REV C C C C C SHEET 15 16 17 18 19 REV STATUS REV C C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Kenneth S. Rice DEFENSE SUPPLY CENTER COLUMBUS CHECKED BY COLUMBUS, OHIO 43218-3990 STANDARD 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-89468 01 X A Drawing number Device type Case outline Lead finish (see 1.2.1) (see 1.2.2) (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number 1/ Circuit function Propagation Delay 01 128-Macrocell EPLD 35 ns 02 128-Macrocell EPLD 30 ns 03 128-Macrocell EPLD 25 ns 04 128-Macrocell EPLD 20 ns 05 128-Macrocell EPLD 15 ns 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X CMGA15-PN 68 pin grid array package 2/ Y GQCC1-J68 68 J-leaded chip carrier 2/ Z See figure 1 68 quad flat package 2/ 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage to ground potential ----------------------- 2.0 V dc to +7.0 V dc DC Input voltage---------------------------------------------- 2.0 V dc to +7.0 V dc Maximum power dissipation 3/--------------------------- 2.5 W Lead temperature (soldering, 10 seconds)------------- +260 C Thermal resistance, junction-to-case ( ): JC Case outlines X and Y------------------------------------- See MIl-STD-1835 Case outline Z ----------------------------------------------- 10C/W 4/ Junction temperature (T)---------------------------------- +175 C J Storage temperature range -------------------------------- -65 C to +150C Temperature under bias ------------------------------------ -55C to +125C Endurance------------------------------------------------------ 25 erase/write cycles (minimum) Data retention------------------------------------------------- 10 years minimum 1.4 Recommended operating conditions. Supply voltage (V ) ---------------------------------------- +4.5 V dc to +5.5 V dc CC Ground voltage (GND) ------------------------------------- 0 V dc Input high voltage (V ) ------------------------------------- 2.2 V dc minimum IH Input low voltage (V ) -------------------------------------- 0.8 V dc maximum IL Case operating temperature range (T ) --------------- -55C to +125C C 1 Generic numbers are listed on the Standard Microcircuit Drawing Source Approval Bulletin at the end of this document and will also be listed in MIL-HDBK-103. 2/ Lid shall be transparent to permit ultraviolet light erasure. 3/ Must withstand the added P due to short circuit test (e.g., I ). D SC 4/ When the thermal resistance for this case is specified in MIL-STD-1835 that value shall supersede the value indicated herein. SIZE STANDARD 5962-89468 A MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS REVISION LEVEL SHEET COLUMBUS, OHIO 43218-3990 C 2 DSCC FORM 2234 APR 97