INCH-POUND
MIL-M-38510/14E
21 March 2005__
SUPERSEDING
MIL-M-38510/14D
2 August 1982
MILITARY SPECIFICATION
MICROCIRCUITS, DIGITAL, TTL, DATA SELECTORS/MULTIPLEXERS,
MONOLITHIC SILICON
Inactive for new design after 7 September 1995.
This specification is approved for use by all Depart-
ments and Agencies of the Department of Defense.
The requirements for acquiring the product herein shall consist of this specification sheet and MIL-PRF 38535
1. SCOPE
1.1 Scope. This specification covers the detail requirements for monolithic, silicon, TTL, data
selectors/multiplexers, logic microcircuits. Two product assurance classes and a choice of case outlines and lead
finishes are provided and are reflected in the complete part number. For this product, the requirements of MIL-M-
38510 have been superseded by MIL-PRF-38535, (see 6.4).
1.2 Part or Identifying Number (PIN). The PIN is in accordance with MIL-PRF-38535, and as specified herein.
1.2.1 Device types. The device types are as follows:
Device type Circuit
01 Sixteen-input data selector/multiplexer, with enable
02, 06 Eight-input data selector/multiplexer, with enable
03 Dual, four-input data selector/multiplexer, with enable
04 Dual, four-input data selector/multiplexer, without enable
05 Quad, two-input data selector/multiplexer, with enable
1.2.2 Device class. The device class is the product assurance level as defined in MIL-PRF-38535.
1.2.3 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows:
Outline letter Descriptive designator Terminals Package style
E GDIP1-T16 or CDIP2-T16 16 Dual-in-line
F GDFP2-F16 or CDFP3-F16 16 Flat-pack
J GDIP1-T24 or CDIP2-T24 24 Dual-in-line
K GDFP2-F24 or CDFP3-F24 24 Flat-pack
Z GDFP7-F24 or CDFP8-F24 24 Flat-pack
Comments, suggestions, or questions on this document should be addressed to: Commander, Defense
Supply Center Columbus, ATTN: DSCC-VAS, P. O. Box 3990, Columbus, OH 43218-3990, or emailed to
bipolar@dscc.dla.mil. Since contact information can change, you may want to verify the currency of this
address information using the ASSIST Online database at MIL-M-38510/14E
1.3 Absolute maximum ratings.
Supply voltage range ...................................................... -0.5 V to +7.0 V
Input voltage range ......................................................... -1.5 V at -12 mA to +5.5 V
Storage temperature range ............................................ -65C to +150C
Maximum power dissipation per gate, (P ) 1/
D
Device type 01 ........................................................ 375 mW
Device types 02 and 06 ........................................... 268 mW
Device type 03 ........................................................ 286 mW
Device type 04 ........................................................ 248 mW
Device type 05 ........................................................ 275 mW
Lead temperature (soldering 10 seconds) ...................... 300C
Thermal resistance, junction-to-case ( )...................... (See MIL-STD-1835)
JC
Junction temperature (T ) 2/.......................................... 175C
J
1.4 Recommended operating conditions.
Supply voltage (V ) ....................................................... 4.5 V minimum to 5.5 V maximum
CC
Minimum high level input voltage (V ) ........................... 2.0 V dc
IH
Maximum low level input voltage (V ) ............................ 0.8 V dc
IL
Maximum low level output current (I ) ............................ 16 mA
IL
Normalized fanout (each output) 3/
Low logic level ......................................................... 10 maximum
High logic level ........................................................ 20 maximum
Case operating temperature range (T ) ......................... -55C to 125C
C
2.0 APPLICABLE DOCUMENT
2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification.
This section does not include documents cited in other sections of this specification or recommended for
additional information or as examples. While every effort has been made to ensure the completeness of this
list, document users are cautioned that they must meet all specified requirements of documents cited in
sections 3, 4, or 5 of this specification, whether or not they are listed.
2.2 Government documents.
2.2.1 Specifications and standards. The following specifications and standards form a part of this specification to
the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATIONS
MIL-PRF-38535 - Integrated Circuits (Microcircuits) Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard for Microelectronics.
MIL-STD-1835 - Interface Standard Electronic Component Case Outlines
(Copies of these documents are available online at