INCH POUND MIL-M-38510/79D 17 AUGUST 2005 SUPERSEDING MIL-M-38510/79C 5 NOVEMBER 1987 MILITARY SPECIFICATION MICROCIRCUITS, DIGITAL, BIPOLAR, SCHOTTKY TTL, DATA SELECTORS / MULTIPLEXERS WITH THREE-STATE OUTPUTS, MONOLITHIC SILICON Inactive for new design after 23 Aug ust 1996. This specification is approved for use by all Depart- ments and Agencies of the Department of Defense. The requirements for acquiring the product herein shall consist of this specification sheet and MIL-PRF 38535. 1. SCOPE 1.1 Scope. This specification covers the detail requirements for monolithic silicon, Schottky TTL, data selectors / multiplexers (three-state) microcircuits. Two product assurance classes and a choice of case outlines and lead finishes are provided and are reflected in the complete part number. For this product, the requirements of MIL-M- 38510 have been superseded by MIL-PRF-38535, (see 6.4). 1.2 Part or Identifying Number (PIN). The PIN is in accordance with MIL-PRF-38535, and as specified herein. 1.2.1 Device type. The device type is as follows: Device type Circuit 01 8 input, data selector / multiplexer 02 Dual, 4-input, data selector / mutiplexer 03 Quad, 2-input, data selector / multiplexer 04 Quad, 2-input, data selector / multiplexer with inverted output 05 8-input, data selector / mutiplexer with 3-state outputs 06 Quad, 2-input, data selector / multiplexer with 3-state outputs 07 Quad, 2-input, data selector / multiplexer with 3-state inverted output 08 Dual, 4-input, data selector / multiplexer with 3-state outputs 1.2.2 Device class. The device class is the product assurance level as defined in MIL-PRF-38535. 1.2.3 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16, CDIP2-T16 16 Dual in line package F GDFP2-F16, CDFP3-F16 16 Flat Package 2 CQCC1-N20 20 Square chip X CQCC2-N20 20 Square chip carrier package Comments, suggestions, or questions on this document should be addressed to: Commander, Defense Supply Center Columbus, ATTN: DSCC-VAS, P. O. Box 3990, Columbus, OH 43218-3990, or emailed to bipolar dscc.dla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at MIL-M-38510/79D 1.3 Absolute maximum ratings. Supply voltage range ...................................................... -0.5 V dc to +7.0 V dc Input voltage range ......................................................... -1.2 V dc at -18 mA to +5.5 V dc Storage temperature range ............................................ -65C to +150C Maximum power dissipation (P ) 1/ : D Device types 01 and 02.............................................. 385 mW Device type 03............................................................ 430 mW Device type 04............................................................ 336 mW Device type 05............................................................ 468 mW Device type 06............................................................ 545 mW Device type 07............................................................ 479 mW Device type 08............................................................ 550 mW Lead temperature (soldering 10 seconds) ...................... 300C Thermal resistance, junction-to-case ( ) : JC Cases E, F, 2, and X .......................................... (See MIL-STD-1835) Junction temperature (T ) 2/.......................................... +175C J 1.4 Recommended operating conditions. Supply voltage (V )........................................................ 4.5 V dc minimum to 5.5 V dc maximum CC Minimum high level input voltage (V ) ........................... 2.0 V dc IH Maximum low level input voltage (V ) ............................ 0.8 V dc 3/ IL Case operating temperature range (T ) ......................... -55C to 125C C 2.0 APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications and standards. The following specifications and standards form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38535 - Integrated Circuits (Microcircuits) Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard for Microelectronics. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines (Copies of these documents are available online at