INCH-POUND MIL-M-38510/112B 18 February 2004 SUPERSEDING MIL-M-38510/112A 27 January 1986 MILITARY SPECIFICATION MICROCIRCUITS, LINEAR, VOLTAGE COMPARATORS, MONOLITHIC SILICON This specification is approved for use by all Departments and Agencies of the Department of Defense. Reactivated after 18 February 2004 and may be used for either new or existing design acquisition The requirements for acquiring the product herein shall consist of this specification sheet and MIL-PRF-38535. 1. SCOPE 1.1 Scope. This specification covers the detail requirements for monolithic silicon, voltage comparators. Two product assurance classes and a choice of case outlines and lead finishes are provided and are reflected in the complete part number. For this product, the requirements of MIL-M-38510 have been superseded by MIL-PRF- 38535, (see 6.3) 1.2 Part or Identifying Number (PIN). The PIN is in accordance with MIL-PRF-38535, and as specified herein. 1.2.1 Device types. The device types are as follows: Device type Circuit 01 Quad voltage comparator, single supply, low power 02 Dual voltage comparator, single supply, low power 1.2.2 Device class. The device class is the product assurance level as defined in MIL-PRF-38535. 1.2.3 Case outline. The case outline are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style A 1/ GDFP5-F14 or CDFP6-F14 14 Flat pack C GDIP1-T14 or CDIP2-T14 14 Dual-in-line D GDFP1-F14 or CDFP2-F14 14 Flat pack P GDIP1-T8 or CDIP2-T8 8 Dual-in-line G MACY1-T8 8 Can 2 CQCC1-N20 20 Square leadless chip carrier 1/ Inactive package case outline. Comments, suggestions, or questions on this document should be addressed to: Commander, Defense Supply Center Columbus, ATTN: DSCC-VAS, 3990 East Broad St., Columbus, OH 43216-5000, or email ed to bipolar dscc.dla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at www.dodssp.daps.mil. AMSC N/A FSC 5962 MIL-M-38510/112B 1.3 Absolute maximum ratings. Positive supply voltage ..................................................................... 36 V Total supply voltage .......................................................................... 36 V or 18 V Output voltage .................................................................................. 36 V Input voltage range ........................................................................... -0.3 V to +36 V 2/ Differential input voltage ................................................................... 36 V Sink current ....................................................................................... 20 mA (approximately) Output short circuit to ground ............................................................ Continuous 3/ Storage temperature range ............................................................... -65C to +150C Junction temperature (T ) ................................................................. +175C 4/ J Lead temperature (soldering, 60 s) .................................................. +300C. 1.4 Recommended operating conditions. Supply voltage (V ) ........................................................................ 5 V dc to 30 V dc CC Operating temperature range ............................................................ -55C to +125C 1.5 Power and thermal characteristics. Case outline Package Maximum allowable maximum maximum power dissipation J-C J-A A, D 14-lead FP 350 mW TA = 125C 60C/W 140C/W C, P Dual-in-line 400 mW T = 125C 35C/W 120C/W A G 8-lead can 330 mW T = 125C 40C/W 150C/W A 2 20-terminal 90 mW T = 125C 55C/W 121C/W A 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this specification, whether or not they are listed. 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications and standards form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. 2/ The input voltage should be within the common mode range to insure a proper output state. 3/ No protection exists for short circuits to the positive supply. 4/ For short term test (in the specific burn-in and life test configuration when required and up to 168 hours maximum) T = 275C. J 2